| SV SLOPE: Set up rising slope (when CRTS = SLOP) |
|
| ANALOG OUT1 MAX.: Adjust upper limit compensation for analog Output 1 (1scale = 1μA; 1scale | 0 |
| = 1mV) | |
|
| |
| ANALOG OUT1 MIN.: Adjust lower limit compensation for analog Output 1* (1 scale = 1μA; 1scale | 0 |
| = 1mV) | |
|
| |
| ANALOG OUT2 MAX.: Adjust upper limit compensation for analog Output 2* (1scale = 1μA; | 0 |
| 1scale = 1mV) | |
|
| |
| ANALOG OUT2 MIN.: Adjust lower limit compensation for analog Output 2* (1scale = 1μA; 1scale | 0 |
| = 1mV) | |
|
| |
| RETRANSMISSION MAX.: Adjust upper limit compensation for Retransmission* (1scale = 1μA; | 0 |
| 1scale = 1mV) (display when a Retransmission Card is connected to DT3) | |
|
| |
| RETRANSMISSION MIN.: Adjust lower limit compensation for Retransmission* (1scale = 1μA; | 0 |
| 1scale = 1mV) (display when a Retransmission Card is connected to DT3) | |
|
| |
| REMOTE GAIN: Adjust Remote gain (When CRTS = REMO) | 0 |
| REMOTE GAIN: Adjust Remote compensation (When CRTS = REMO) | 0 |
| REMOTE LOW: Remote lower limit (When CRTS=REMO) | 0 |
| REMOTE HIGH: Remote higher limit (When CRTS=REMO) | 100 |
| EVENT1: Set up EVENT1 function (display when a Event Card is connected to EVENT1) | 0 |
| EVENT2: Set up EVENT2 function (display when a Event Card is connected to EVENT2) | 0 |
|
|
|
| EVENT3: Set up EVENT3 function (display when a Event Card is connected to EVENT3) | 0 |
PID mode: Any of the 6 PID groups can be selected. When set to AUTO mode, the program will automatically select the PID group that is the closest to the target temperature.
Select 0~5 group of PID and execute AT function, the system will automatically load P; I; D and IOF parameters into the selected PID group.
Select the nth PID (n = 0 ~ 5) |
|
|
|
|
|
| press | to set 0 ~ 5th PID parameters |
| |||||
Set up the 0th PID temperature value |
|
|
| ~ |
|
|
| Set up the 5th PID temperature value |
| |||||
|
|
| press | V |
|
|
|
|
|
|
| press | V | |
|
|
|
|
|
|
|
|
|
|
| ||||
Set up the 0th proportional band value |
|
|
| ~ |
|
|
| Set up the 5th proportional band value |
| |||||
Set up the 0th Ti value |
|
|
|
|
| ~ |
|
|
| Set up the 5th Ti value |
|
| ||
Set up the 0th Td value |
|
|
|
| ~ |
|
|
| Set up the 5th Td value |
|
| |||
Set up the 0th PID integral deviation |
|
|
| ~ |
|
|
| Set up the 5th PID integral deviation |
| |||||
| Press | to set the parameters in |
|
|
|
|
|
| Press | to set the parameters in |
| |||
|
| “Regulation Mode” |
|
|
|
|
|
|
| “Regulation Mode” |
| |||
Programmable Editing: set | to | or |
|
| and set |
| to | . |
|
|
|
| ||
|
|
|
|
|
|
|
| |||||||
Select desired editing pattern number 0~F |
|
|
|
| press | to set the desired editing pattern number 0~F |
| |||||||
|
| If the setting is OFF, leave the editing pattern page and go to | to continue with the setting. | |||||||||||
Edit the temperature of step No.0 of pattern No. 0 |
| ~ |
|
| Edit the temperature of step No.0 of pattern No. 15 | |||||||||
|
|
| press |
| V |
|
|
|
|
|
|
|
|
|
Edit the time of step No.0 of pattern No. 0 (time unit: |
| ~ |
|
| Edit the time of step No.0 of pattern No.15 (time unit: | |||||||||
hh, mm) |
|
|
|
|
|
|
| hh, mm) |
|
|
|
| ||
~ | Set up step 0~15 in order |
|
|
| ~ |
|
|
|
|
|
|
| ||
Edit the temperature of step No.15 of pattern No.0 |
| ~ |
|
| Edit the temperature of step No.15 of pattern No.15 | |||||||||
Edit the time of step No.15 of pattern No.0 |
|
|
| ~ |
|
| Edit the time of step No.15 of pattern No.15 |
| ||||||
Seelect the actual required steps for executing |
| ~ |
|
| Seelect the actual required steps for executing | |||||||||
pattern No.0 |
|
|
|
|
|
|
| pattern No.15 |
|
|
|
| ||
Set up the additional cycle (0~199) for pattern No. |
| ~ |
|
| Set up the additional cycle (0~199) for pattern No. | |||||||||
0 execution |
|
|
|
|
|
|
| 15 execution |
|
|
|
| ||
Set up the link pattern of pattern No.0 (0~F; |
| ~ |
|
| Set up the link pattern of pattern No.15 (0~F; |
| ||||||||
END; STOP) |
|
|
|
|
|
|
| END; STOP) |
|
|
|
| ||
|
| Press | to return to the |
|
|
|
|
|
| Press | to return to the | |||
| selection of desire editing pattern and number. |
|
|
|
|
| selection of desire editing pattern and number | |||||||
5