Invacare Excelerator XLT 2000, Li'l Execelerator manual Fork/Spring/Crank

Page 15

FORK/SPRING/CRANK

PROCEDURE 5

EXCELERATOR XLT/XLT 2000 FORK/CRANK ASSEMBLY REPLACEMENT (FIGURE 3)

NOTE: Invacare recommends that the following proce- dure be performed by a qualified technician.

1. Note the position of the crank handles.

2.Loosen, but do not remove the two (2) socket screws that secure the crank handles to the existing fork.

3.Slide the crank handles down towards the front wheel.

4.Remove the chain from the crank handles.

5.Remove the crank handles from the existing fork.

6.Remove the two (2) socket screws and half clamp that secure the brake handle to the existing fork.

7.Remove the socket nut on the BACK of the existing fork that secures the brake assembly.

F O R K

/

S P R I N G

STEPS 1, 2, 3, 38, 39

Socket

Screws

Fork

Crank

Handles

STEPS 6, 36

Fork Brake

Handle

Half

Clamp

Socket

Screws

STEPS 7, 8, 35

ForkHardware

Socket

Nut

Brake Assembly

/

C R A N K

STEPS 9, 34

Fork

Road Crown Compensator

STEPS 10, 33

Seat Frame Shifter

STEPS 11, 12, 31, 32

 

 

ut

Brake

Lockn

 

 

Arm

 

 

 

 

Clamp

Brake

He

x Bo

lt

 

 

 

Arm

 

 

 

STEPS 13, 14, 27, 28, 29, 30

Non-Turn Fork

Washer - Must

Be Installed

as Shown

Washer

 

Front

Cap Nuts

Wheel

 

STEPS 16, 17, 24, 25

Fork

Hex

Bolts,

Locknuts

and

Footrest

Footrest

Clamps

STEPS 5, 18, 19, 20, 21, 22, 23, 37

Crank Handles

Top

Nuts

Bearing

O-Ring

Bottom Bearing

Frame

Fork

FIGURE 3 - EXCELERATOR XLT/XLT 2000 FORK/CRANK ASSEMBLY REPLACEMENT

15

Image 15
Contents Excelerator Lil Excelerator Excelerator XLT E C I a L T E S Special NotesTable of Contents Specifications Specification SOperating Information General GuidelinesStability and Balance SAFETY/HANDLING ExceleratorProcedure Percentage of Weight DistributionHand Crank Footrest Seat Frame Procedure Safety Inspection ChecklistSuggested Maintenance Procedures MaintenanceSafety INSPECTION/TROUBLESHOOTING/MAINTENANCE Maintenance Safety PrecautionsEXCELERATOR/LIL Excelerator Assembly Procedures Figure Assembly Procedures Excelerator XLT/XLT 2000 Assembly Procedures FigureA R INSTALLING/ADJUSTING the Rear Wheel QUICK-RELEASE AxlesA R E E L S Adjusting Toe In/Toe OutReplacing Camber Inserts Figure Rear WheelsExcelerator XLT/XLT FORK/SPRING/CRANK Excelerator XLT/XLT 2000 FORK/CRANK Assembly ReplacementRemoving Tension Spring Tension Spring Replacement/Adjustment FigureRoad Crown Compensator Replacement/ Adjustment Figure Adjusting Tension SpringE E D I F T E R S LIL Excelerator Three 3 Speed Shifter Cable AdjustmentProcedure a Figure Procedure B FigureSlot Clickbox Opening Speed ShiftersA I N EXCELERATOR/LIL Excelerator Chain AdjustmentChain Excelerator XLT Chain AdjustmentReplacement Using Parking Brake FigureParking Brake ADJUSTMENT/ Replacement Figure AdjustmentBACK/SEAT C K A TExcelerator/Lil Excelerator Figure Excelerator XLT/XLT 2000 Figure Excelerator XLT/XLT 2000 Back Angle Adjustment FigureH O L S T E R Y Seat Upholstery Replacement FigureBack Upholstery Replacement UpholsteryO T R E S T Adjusting Footrest HeightAdjusting Footrest Angle Adjusting Footrest DepthFootrest FootrestLeg Guard Excelerator XLT/XLT USING/REPLACING Footrest Strap Using Footrest Strap FigureReplacing Footrest Strap Figure E R a T I O N Hand Crank AssemblyShifting Gears OperationParking Brake Procedure OperationBACKING-UP BrakingSTEERING/CORNERING Operation ProcedureAdjusting Gear Shift Push Button Figure Bearing Play Adjustment FigureSeat Positioning Strap Installation Figure Water Bottle Installation FigureRear Safety Light Figure Computer Installation FigureSafety Helmet Figure Procedure OptionsLateral Support Figure R R a N T Y WarrantyOne InvacareWay