Invacare II250 SERIES, IIJR, IIBASIC manual Raising/Lowering Elevating Legrests, Adjusting Calfpads

Page 23

FRONT RIGGINGS

PROCEDURE 3

RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS (FIGURE 6)

Raising/Lowering Elevating Legrests

1.Perform one (1) of the following:

RAISING - Pull back on the release lever

until the leg is at the desired height.

LOWERING - Support leg with one (1) hand and push release lever down- ward with other hand.

Adjusting Calfpads

1.Turn calfpad towards the outside of the wheelchair.

2.Slide the calfpad up or down until the desired position is obtained.

NOTE: If one (1) of the top two (2) calfpad adjustment positions is being used, the legrest will need to be raised to avoid interference with the front stabilizers while going over obstacles or going up and down ramps. Refer to RAISING/LOWERING ELEVATING LEGRESTS in this procedure of the manual.

3. Turn the calfpad towards the inside of the wheelchair.

Release Lever

Calfpad

Rotated for

Height

Adjustment

Calfpad

Top Two (2) Calfpad

Adjustment Positions

FIGURE 6- RAISING/LOWERING ELEVATING LEGRESTS AND/OR ADJUSTING CALFPADS

ADJUSTING/REPLACING TELESCOPING FRONT RIGGING SUPPORT (FIGURE 7)

1.Lift up on the crossbraces until they release from the H-blocks on the wheelchair frame.

2.Remove the phillips bolt and locknut that secure the front H-block to the wheelchair frame.

3.Remove the two (2) locknuts and socket bolts that secure telescoping front rigging support to wheelchair.

4.If necessary, remove the hex bolt and locknut that secures the battery charger connector bracket to the wheelchair.

Adjusting

1.Position the telescoping front rigging support to the desired depth.

NOTE: The footplate will be on the inside of the wheel- chair when locked in place.

2.Insertfrontsocketboltintowheelchairframeandmount- ing hole in the telescoping front rigging support deter- mined in STEP 1 and securely tighten with the locknut.

3.Insert the rear socket bolt through the wheelchair frame and the telescoping front rigging support and securely tighten with the locknut.

4.Resecure the front H-block to the wheelchair with the phillips bolt and locknut.

5.If necessary, resecure the battery charger con- nector bracket to the wheelchair with the two (2) hex bolts and locknuts.

6.Snap crossbraces into H-blocks. Wiggle crossbraces to make sure they are secured in the H-blocks.

Phillips Bolt

 

H-Block

FRONT SOCKET BOLT

 

POSITIONS (IN

Front Socket Bolt

INCHES DEEP):

Rear

16

Socket Bolt

18 and

 

17

Wheelchair

Frame

Locknuts

DO NOT USE WITH FRONT

Telescoping

SOCKET BOLT

Front Rigging

Hex Bolt and

Support

 

Locknut

 

Battery

Charger

Bracket

FIGURE 7 - ADJUSTING/REPLACING TELESCOPING

FRONT RIGGING SUPPORT

F R O N T

R

I

G G I N G S

23

Image 23
Contents MWD/FWD Wheelchair TIE-DOWN Restraints and Seat Positioning Straps R N I N GTable of Contents Performance Specification SIntegrated Sling Seat Captainsseat Electronics SpecificationsRain and operators weight PerformanceIntegrated Sling Seat Procedure 1 of this manualGeneral Guidelines ProcedureGeneral Guidelines ProcedureCoping With Everyday Obstacles SAFETY/HANDLING WheelchairsStability and Balance StairwaysRII FWD Model Wheelchairs only Figure Shift body weight into seat with transferMinimize GAP Distance RII MWD Wheelchairs onlyReaching, Leaning, Bending and Bending Forward Functional Reach From a WheelchairReaching, Bending Backward General Guidelines Push Bracket CrossbraceRanger II BASIC/RANGER II STANDARD/RANGER II 250 Series General GuidelinesprocedureBack View Motor Assembly BatterySide Frame Controller Part numberShipping Insert Removed Shipping Insert InstalledShipping Insert Battery Box Safety INSPECTION/TROUBLESHOOTING Troubleshooting MechanicalTroubleshooting Electrical Checking Battery Charge LevelNumber of Floating Balls Will Vary According to Charge Safety INSPECTION/TROUBLESHOOTINGUsing Hydrometer to Check Battery Cells Lead Acid Figure Number of Floating BallsArms Procedure Safety Inspection ChecklistO N T I N G S INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height Front RiggingsModel Footrests Procedure Front RiggingsP93M Model Footrests Figure Lug Bolt Footrest Support Locknut LowerRaising/Lowering Elevating Legrests Adjusting CalfpadsAdjusting Depth All Models Figure Adjusting Removable FootboardAdjusting Footboard Angle ALL Models Figure ReplacingFront Hex ScrewFootboard Pivot Caplug Assemblies Washer Battery TrayRemoving The Removable Footboard Plate Installing The Removable Footboard PlateM S INSTALLING/REMOVING Flip Back Armrests FigureAdjusting Flip Back Armrests Figure ArmsHeight Figure Adjusting Captains Seat ArmrestsProcedure Arms Positioning Flip Back Armrests for UseH O L S T E R Y P T a I N S A T Adjusting Captains Seat FigureReplacing Seat Upholstery Figure UPHOLSTERY/CAPTAINS SEAT/POSITIONING StrapIntegrated Sling Seat Models Figure REMOVING/INSTALLING Captains Seat FigureReplacing Seat Positioning Strap UPHOLSTERY/CAPTAINS SEAT/POSITIONING StrapElectronics Mkiv Joystick Adjustment JoystickLock MountingTubePreparing Mkiv Joystick for USE Figure Repositioning Mkiv JoystickPerform one 1 of the following SwitchElectronics Battery FuseWiringHarness Holder Fuse ReplacementAll MWD Models and FWD Model Ranger Iijr Figure Replacing Battery BOX Retaining StrapT a I N I N G Retaining StrapAll FWD Models Except Ranger Iijr Figure Hex Bolt Battery Tray Tray Support LocknutRetaining Strap T a I N I N G R a POutside of Wheelchair Front of Wheelchair ENGAGING/DISENGAGING Motors with Motor Locks FigureE E L S WheelsDust Cover Locknut Nylon Washer Caster Headtube Fork Adjusting Forks FigureWheels Remove the dust cover from the caster headtubeShrouds REMOVING/INSTALLING ShroudsR O U D S Shrouds REMOVING/INSTALLING Shrouds MWD WheelchairsRemoving Rear Shroud Installing Rear ShroudFWD Wheelchairs Figure Clip Retaining Strap Battery BoxRear Shroud Inch wide chairs Clip Batteries T T E R I E SDual U1 Batteries Connecting Battery CablesBatteries Direct Mount Method , 3Connect Battery Cable to Battery Terminal AS Shown Connect Battery Cables Ring Terminals to This Side PostsInstalling Battery Clamp Covers Battery Clamp Method Figures 4, 5Fuse Box RED Battery Clamp CoverNegative Battery Terminal/Post Tie-Wrap Group 22NF Battery E R I E SUnfolding Transporting Ranger II FWDFWD Wheelchairs E E L C H a I R SMCC-MKIV X, a or A+ Joystick When to Charge Batteries FigureFWD Wheelchairs Mkiv RII JoystickReplacing Batteries Description and Use of Battery ChargersShutoff Procedure Charging Batteries FigureCleaning Battery Terminals INSTALLING/REMOVING Battery BoxesRecommended Battery Types Ranger Iijr Figure Rear BatteryJoystick Cable ALL Models Except Ranger IijrUnfolding Battery Tray for Use Figure Battery TrayProcedure 11FWD Wheelchairs Folding Battery Tray for Transport FigureRanger Iibasic and Ranger Iistandard Pins Pivot Battery TrayNotch Battery Tray Hanger Bracket Pins Mounting Battery Tray SlotsUnfolding/Folding Integrated Sling Seats Figure Transporting Ranger II MWDE E L C H a I R MWD WheelchairsPush Brackets Crossbraces Battery Discharge Indicator BDI Battery Gauge Display BGDMWD Wheelchairs Refer to DisconnectIf necessary, remove the rear shroud. Refer to RE A I R SProng plug, 15 ampere current rating industrial type Detail a Leads INSTALLING/REMOVING Battery Boxes FigureRetaining Front Battery Box Strap Rear Strap Clip Installing Battery Tray Adjusting the Stabilizer FigureBattery Tray Figure Additional Adjustments for User Preference Detail BLimited Warranty