Invacare IISTANDARD REMOVING/INSTALLING Captains Seat Figure, Replacing Seat Positioning Strap

Page 30

PROCEDURE 5

UPHOLSTERY/CAPTAIN'S SEAT/POSITIONING STRAP

 

 

 

U P H O L S T E R Y

C A P T A I N S

S E A T

P O S I T I O N I N G

S T R A P

REMOVING/INSTALLING CAPTAIN'S SEAT (FIGURE 3)

Removing

1.Turn the adjustment lock lever to release the joystick mounting tube from the armrest.

2.Remove the joystick from the wheelchair.

3.HIGH BACK CAPTAIN'S SEATS ONLY - Discon- nect the limit switch. Refer to DISCONNECTING/ CONNECTING LIMIT SWITCH in PROCEDURE 6 of this manual.

4.Remove the four (4) quick release pins that secure the Captain's Seat to the wheelchair frame.

5.Remove the Captain's Seat from the wheelchair.

Installing

1.Push the Captain's Seat down on the wheelchair frame at the position shown in FIGURE 3.

2.Line up the mounting holes in the Captain's Seat and the wheelchair frame.

WARNING

Make sure the Captain's Seat is secured to the wheelchair frame with the four (4) quick release pins BEFORE using the wheelchair, otherwise in- jury or damage can occur.

Armrest

Joystick

 

Captain's

 

Seat

Joystick

 

Mounting

 

Tube

 

Adjustment

 

Lock Lever

 

Mounting

Holes

Wheelchair

Frame

Quick Release Pins

FIGURE 3- REMOVING/INSTALLING CAPTAIN'S SEAT

3.Insert the four (4) quick release pins through the mounting holes in the Captain's Seat and the wheel- chair frame until the rings on the quick release pins are against the mounting holes.

4.Lift up on the Captain's Seat to make sure it is se- cured to the wheelchair frame.

5.HIGH BACK CAPTAIN'S SEATS ONLY - Connect the limit switch. Refer to DISCONNECTING/CON- NECTING LIMIT SWITCH in PROCEDURE 6 of this manual.

6.Slide the joystick into the adjustment lock lever to the desired position.

7.Turn the adjustment lock lever to secure the joystick mounting tube to the armrest.

REPLACING SEAT POSITIONING STRAP

Integrated Sling Seat Models (FIGURE 4)

1.If necessary, remove the seat cushion from the seat upholstery.

2.Remove the two (2) rear phillips screws and washers that secure the seat upholstery and existing seat po- sitioning strap to the crossbraces.

3.Remove the two (2) halves of the seat positioning strap from the crossbraces.

4.Position the two (2) new seat positioning strap halves between the seat upholstery and the crossbraces.

5.Reinstall the rear phillips screws and washers that secure the seat upholstery and seat positioning strap to the crossbraces.

NOTE: Washer is positioned on top of seat upholstery.

6.If necessary, reinstall seat cushion onto seat uphol- stery.

Washer

Phillips Screw

Seat Upholstery

Crossbrace

Seat Positioning Strap

FIGURE 4 - REPLACING SEAT POSITIONING STRAP -

INTEGRATED SLING SEAT MODELS

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents MWD/FWD R N I N G Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsTable of Contents Specification S Integrated Sling Seat CaptainsseatPerformance Performance SpecificationsRain and operators weight ElectronicsProcedure 1 of this manual Integrated Sling SeatProcedure General GuidelinesProcedure General GuidelinesStairways SAFETY/HANDLING WheelchairsStability and Balance Coping With Everyday ObstaclesRII MWD Wheelchairs only Shift body weight into seat with transferMinimize GAP Distance RII FWD Model Wheelchairs only FigureFunctional Reach From a Wheelchair Reaching, Leaning, Bending and Bending ForwardReaching, Bending Backward General Guidelines Crossbrace Push BracketGeneral Guidelinesprocedure Ranger II BASIC/RANGER II STANDARD/RANGER II 250 SeriesController Part number Motor Assembly BatterySide Frame Back ViewShipping Insert Installed Shipping Insert Battery BoxShipping Insert Removed Checking Battery Charge Level Troubleshooting MechanicalTroubleshooting Electrical Safety INSPECTION/TROUBLESHOOTINGNumber of Floating Balls Safety INSPECTION/TROUBLESHOOTINGUsing Hydrometer to Check Battery Cells Lead Acid Figure Number of Floating Balls Will Vary According to ChargeSafety Inspection Checklist Arms ProcedureFront Riggings INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height O N T I N G SLug Bolt Footrest Support Locknut Lower Procedure Front RiggingsP93M Model Footrests Figure Model FootrestsAdjusting Calfpads AdjustingRaising/Lowering Elevating Legrests Replacing Adjusting Removable FootboardAdjusting Footboard Angle ALL Models Figure Depth All Models FigureBattery Tray Front Hex ScrewFootboard Pivot Caplug Assemblies WasherInstalling The Removable Footboard Plate Removing The Removable Footboard PlateArms INSTALLING/REMOVING Flip Back Armrests FigureAdjusting Flip Back Armrests Figure M SPositioning Flip Back Armrests for Use Adjusting Captains Seat ArmrestsProcedure Arms Height FigureUPHOLSTERY/CAPTAINS SEAT/POSITIONING Strap Adjusting Captains Seat FigureReplacing Seat Upholstery Figure H O L S T E R Y P T a I N S A TUPHOLSTERY/CAPTAINS SEAT/POSITIONING Strap REMOVING/INSTALLING Captains Seat FigureReplacing Seat Positioning Strap Integrated Sling Seat Models FigureRepositioning Mkiv Joystick Mkiv Joystick Adjustment JoystickLock MountingTubePreparing Mkiv Joystick for USE Figure ElectronicsSwitch ElectronicsPerform one 1 of the following Fuse Replacement Battery FuseWiringHarness HolderRetaining Strap Replacing Battery BOX Retaining StrapT a I N I N G All MWD Models and FWD Model Ranger Iijr FigureT a I N I N G R a P Hex Bolt Battery Tray Tray Support LocknutRetaining Strap All FWD Models Except Ranger Iijr FigureWheels ENGAGING/DISENGAGING Motors with Motor Locks FigureE E L S Outside of Wheelchair Front of WheelchairRemove the dust cover from the caster headtube Adjusting Forks FigureWheels Dust Cover Locknut Nylon Washer Caster Headtube ForkREMOVING/INSTALLING Shrouds R O U D SShrouds REMOVING/INSTALLING Shrouds MWD Wheelchairs ShroudsInstalling Rear Shroud FWD Wheelchairs FigureRemoving Rear Shroud Battery Box Rear Shroud Inch wide chairs ClipClip Retaining Strap T T E R I E S BatteriesDirect Mount Method , 3 Connecting Battery CablesBatteries Dual U1 BatteriesConnect Battery Cables Ring Terminals to This Side Posts Connect Battery Cable to Battery Terminal AS ShownBattery Clamp Method Figures 4, 5 Installing Battery Clamp CoversE R I E S RED Battery Clamp CoverNegative Battery Terminal/Post Tie-Wrap Group 22NF Battery Fuse BoxE E L C H a I R S Transporting Ranger II FWDFWD Wheelchairs UnfoldingMkiv RII Joystick When to Charge Batteries FigureFWD Wheelchairs MCC-MKIV X, a or A+ JoystickCharging Batteries Figure Description and Use of Battery ChargersShutoff Procedure Replacing BatteriesINSTALLING/REMOVING Battery Boxes Recommended Battery TypesCleaning Battery Terminals ALL Models Except Ranger Iijr Rear BatteryJoystick Cable Ranger Iijr FigureFolding Battery Tray for Transport Figure Battery TrayProcedure 11FWD Wheelchairs Unfolding Battery Tray for Use FigureHanger Bracket Pins Mounting Battery Tray Slots Pins Pivot Battery TrayNotch Battery Tray Ranger Iibasic and Ranger IistandardMWD Wheelchairs Transporting Ranger II MWDE E L C H a I R Unfolding/Folding Integrated Sling Seats FigureRefer to Disconnect Battery Discharge Indicator BDI Battery Gauge Display BGDMWD Wheelchairs Push Brackets CrossbracesA I R S Prong plug, 15 ampere current rating industrial typeIf necessary, remove the rear shroud. Refer to RE Detail a INSTALLING/REMOVING Battery Boxes Figure Retaining Front Battery Box Strap Rear Strap ClipLeads Additional Adjustments for User Preference Detail B Adjusting the Stabilizer FigureBattery Tray Figure Installing Battery TrayLimited Warranty
Top Page Image Contents