Invacare IISTANDARD, IIJR, IIBASIC, II250 SERIES manual T T E R I E S, Batteries

Page 42

PROCEDURE 10

BATTERIES

B A T T E R I E S

This Procedure includes the following:

Installing/Removing Batteries into/From Battery Boxes

Connecting Battery Cables

WARNING

Make sure power to the wheelchair is OFF be- fore performing this procedure.

The use of rubber gloves and safety glasses is rec- ommended when working with batteries.

Invacare strongly recommends that battery in- stallation and battery replacement ALWAYS be done by a qualified technician.

After ANY adjustments, repair or service and BE- FORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result.

NOTE: For additional battery information, refer to PROCEDURE 11 - FWD wheelchairs or PROCE- DURE 12 - MWD wheelchairs.

INSTALLING/REMOVING BATTERIES INTO/FROM BATTERY BOXES (FIGURE 1)

NOTE:Toremovethebattery(ies) fromthebatterybox(es), reverse the following procedure.

NOTE: Have the following tools available:

TOOL

QTY

COMMENTS

 

 

 

Battery Lifting Strap

1

See Note

1/2-inch (6 pt) Box Wrench

1

Not Supplied

7/16-inch (6pt) Box Wrench

1

Not Supplied

3/8-inch (6pt) Box Wrench

1

Not Supplied

Diagonal Cutters

1

Not Supplied

 

 

 

*NOTE: The Battery Lifting strap supplied is for Group 22 NF Batteries ONLY. Refer to the battery manufac- turer for the proper lifting strap and/or battery tools for U1 battery removal/installation.

WARNING

ALWAYS use a battery lifting strap when lifting a battery. It is the most convenient method and assures that the battery acid will not spill. It also helps to prolong the life of the battery.

DO NOT tip the batteries. Keep the batteries in an upright position.

NOTE: If there is battery acid in the bottom or on the sides of the battery box(es) or battery(ies), apply baking soda to these areas to neutralize the battery acid. Before reinstalling the NEW or existing battery(ies), clean the baking soda from the battery box(es) or battery(ies).

NOTE: When securing battery lifting strap to battery, observe polarity markings located on the ends of the battery lifting strap, (+) side to POSITIVE (+) battery terminal/post and (-) side to NEGATIVE (-) battery ter- minal/post.

1.If necessary, remove the battery boxes from the wheelchair. Refer to INSTALLING/REMOVING BAT- TERY BOXES in PROCEDURE 11 - FWD or PRO- CEDURE 12 - MWD of this manual.

2.Secure the battery lifting strap to battery terminal(s)/ post(s) (FIGURE 1).

CAUTION

Somebatterymanufacturersmoldacarryingstrap and/or hold down flanges directly into the bat- tery case. Batteries which interfere with the bat- tery box cannot be used for these applications. Attempting to “wedge” a battery into a battery box may damage the box and/or the battery.

3. Place batteries into battery box bottom.

Battery Lifting Strap

Molded Carrying Strap

Or Hold Down Flanges

Battery

Group 22 NF ONLY

Battery Terminal(s)/Post(s)

U1 Battery Box

Bottom

Group 22 NF

Battery Box

Bottom

FIGURE 1 - INSTALLING/REMOVING BATTERIES INTO/

FROM BATTERY BOXES

42

Image 42
Contents MWD/FWD R N I N G Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsTable of Contents Specification S Integrated Sling Seat CaptainsseatPerformance Performance SpecificationsRain and operators weight ElectronicsProcedure 1 of this manual Integrated Sling SeatProcedure General GuidelinesProcedure General GuidelinesStairways SAFETY/HANDLING WheelchairsStability and Balance Coping With Everyday ObstaclesRII MWD Wheelchairs only Shift body weight into seat with transferMinimize GAP Distance RII FWD Model Wheelchairs only FigureFunctional Reach From a Wheelchair Reaching, Leaning, Bending and Bending ForwardReaching, Bending Backward General Guidelines Crossbrace Push BracketGeneral Guidelinesprocedure Ranger II BASIC/RANGER II STANDARD/RANGER II 250 SeriesController Part number Motor Assembly BatterySide Frame Back ViewShipping Insert Installed Shipping Insert Battery BoxShipping Insert Removed Checking Battery Charge Level Troubleshooting MechanicalTroubleshooting Electrical Safety INSPECTION/TROUBLESHOOTINGNumber of Floating Balls Safety INSPECTION/TROUBLESHOOTINGUsing Hydrometer to Check Battery Cells Lead Acid Figure Number of Floating Balls Will Vary According to ChargeSafety Inspection Checklist Arms ProcedureFront Riggings INSTALLING/REMOVING Footrests FigureAdjusting Footrest Height O N T I N G SLug Bolt Footrest Support Locknut Lower Procedure Front RiggingsP93M Model Footrests Figure Model FootrestsAdjusting Calfpads AdjustingRaising/Lowering Elevating Legrests Replacing Adjusting Removable FootboardAdjusting Footboard Angle ALL Models Figure Depth All Models FigureBattery Tray Front Hex ScrewFootboard Pivot Caplug Assemblies WasherInstalling The Removable Footboard Plate Removing The Removable Footboard PlateArms INSTALLING/REMOVING Flip Back Armrests FigureAdjusting Flip Back Armrests Figure M SPositioning Flip Back Armrests for Use Adjusting Captains Seat ArmrestsProcedure Arms Height FigureUPHOLSTERY/CAPTAINS SEAT/POSITIONING Strap Adjusting Captains Seat FigureReplacing Seat Upholstery Figure H O L S T E R Y P T a I N S A TUPHOLSTERY/CAPTAINS SEAT/POSITIONING Strap REMOVING/INSTALLING Captains Seat FigureReplacing Seat Positioning Strap Integrated Sling Seat Models FigureRepositioning Mkiv Joystick Mkiv Joystick Adjustment JoystickLock MountingTubePreparing Mkiv Joystick for USE Figure ElectronicsSwitch ElectronicsPerform one 1 of the following Fuse Replacement Battery FuseWiringHarness HolderRetaining Strap Replacing Battery BOX Retaining StrapT a I N I N G All MWD Models and FWD Model Ranger Iijr FigureT a I N I N G R a P Hex Bolt Battery Tray Tray Support LocknutRetaining Strap All FWD Models Except Ranger Iijr FigureWheels ENGAGING/DISENGAGING Motors with Motor Locks FigureE E L S Outside of Wheelchair Front of WheelchairRemove the dust cover from the caster headtube Adjusting Forks FigureWheels Dust Cover Locknut Nylon Washer Caster Headtube ForkREMOVING/INSTALLING Shrouds R O U D SShrouds REMOVING/INSTALLING Shrouds MWD Wheelchairs ShroudsInstalling Rear Shroud FWD Wheelchairs FigureRemoving Rear Shroud Battery Box Rear Shroud Inch wide chairs ClipClip Retaining Strap T T E R I E S BatteriesDirect Mount Method , 3 Connecting Battery CablesBatteries Dual U1 BatteriesConnect Battery Cables Ring Terminals to This Side Posts Connect Battery Cable to Battery Terminal AS ShownBattery Clamp Method Figures 4, 5 Installing Battery Clamp CoversE R I E S RED Battery Clamp CoverNegative Battery Terminal/Post Tie-Wrap Group 22NF Battery Fuse BoxE E L C H a I R S Transporting Ranger II FWDFWD Wheelchairs UnfoldingMkiv RII Joystick When to Charge Batteries FigureFWD Wheelchairs MCC-MKIV X, a or A+ JoystickCharging Batteries Figure Description and Use of Battery ChargersShutoff Procedure Replacing BatteriesINSTALLING/REMOVING Battery Boxes Recommended Battery TypesCleaning Battery Terminals ALL Models Except Ranger Iijr Rear BatteryJoystick Cable Ranger Iijr FigureFolding Battery Tray for Transport Figure Battery TrayProcedure 11FWD Wheelchairs Unfolding Battery Tray for Use FigureHanger Bracket Pins Mounting Battery Tray Slots Pins Pivot Battery TrayNotch Battery Tray Ranger Iibasic and Ranger IistandardMWD Wheelchairs Transporting Ranger II MWDE E L C H a I R Unfolding/Folding Integrated Sling Seats FigureRefer to Disconnect Battery Discharge Indicator BDI Battery Gauge Display BGDMWD Wheelchairs Push Brackets CrossbracesA I R S Prong plug, 15 ampere current rating industrial typeIf necessary, remove the rear shroud. Refer to RE Detail a INSTALLING/REMOVING Battery Boxes Figure Retaining Front Battery Box Strap Rear Strap ClipLeads Additional Adjustments for User Preference Detail B Adjusting the Stabilizer FigureBattery Tray Figure Installing Battery TrayLimited Warranty