Invacare 1171880 Changing Wheel Lock Handle Position, Replacing/Adjusting the Wheel Locks

Page 64

10 WHEEL LOCKS

5.Repeat the above procedures until the wheel locks hold the wheelchair.

Push-to-Lock or Pull-to-Lock Wheel Locks					Under Mount Wheel Lock
Mounting Screws	3/16 inch				Mounting Screws	3/16 inch
	(1/8-inch)					(1/8-inch)

	Wheel		Wheel Lock	Wheel Lock		Wheel Lock
	Lock	Tire			Tire	Shoe
			Shoe

FIGURE 1 Replacing/Adjusting the Wheel Locks

10.2 Changing Wheel Lock Handle Position

1.Loosen, but DO NOT remove, the rear handle mounting screw.

2.Remove the front handle mounting screw and locknut.

3.Align the front handle mounting hole with one of three desired mounting positions on the wheel lock.

4.Using the front handle mounting screw and locknut, secure the handle to the wheel lock.

5.Securely tighten the front and rear handle mounting screws and locknuts.

6.Repeat STEPS 1-5 on remaining wheel lock handle.

Wheel lock

Handle

Mounting

Positions

	Rear Handle	Front Handle
		Mounting Screw
	Mounting Screw
		and Locknut

	FIGURE 2 Changing Wheel Lock Handle Position

Invacare®Top End Reveal™Wheelchair

64

Part No 1171880

Image 64

Contents InvacareTop End RevealWheelchair Page Contents Seat Caster Symbols GeneralLimited Warranty General Guidelines SafetyWheelchair User Wheelchair Tie Down Restraints Stability WarningRepair and Service Information Operating InformationSeat Positioning Straps Weight TrainingTire Pressure and Information Overview Label Locations Serial NumberComponent Identification Typical Product Parameters 0, +4, +8Non Tapered front end Standard Lock Down, Folding StandardReveal RVL Weight Safety/Handling of Wheelchairs Safety/Handling of WheelchairsStability and Balance SAFETY/HANDLING of Wheelchairs Lengthening Wheelbase Shortening Reaching, Leaning and Bending ForwardReaching, Leaning Bending Forward Backwards Reaching, Leaning BackwardsCoping with Everyday Obstacles Tipping Tipping CurbsStairways Moving Up StairsMoving Down Stairs StairwaysEscalators Transferring To and From Other SeatsSafety Inspection Checklist Safety InspectionInspect Initially Inspect/Adjust Weekly Inspect/Adjust Monthly Inspect/Adjust PeriodicallyTroubleshooting SolutionsMaintenance Maintenance Safety Precautions Suggested Maintenance Procedures Tire wear is excessive if Replacing/Repairing Rear Wheel Tire/Tube Replacing/Repairing Caster Tire/TubeAdjusting the Footrest Adjusting/Replacing Standard FootrestFootrest Replacing/Adjusting Optional Adjustable Angle Footrest Replacing the FootrestAdjusting Footplate Angle Adjusting Footplate DepthAdjustments Clamp Replacing/Adjusting Optional Adjustable Angle FootrestInstalling the Swingaway Padded Armrest Socket ArmsRemove Back Stop Insert Right Side Armrest Socket Left Side Armrest SocketInstall Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Adjusting Height Installing/Removing/Adjusting the Swingaway Padded ArmrestRemoving  To remove the T-arm, reverse this procedure Adjusting T-Arm HeightBack Unfolding/Folding the BackDetail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail Hole in adjustment When installedThis orientation Square will align withHole Adjustment Square will align with + when installedWith 0 when Seat Rail OrientationAdjustable Tension Back Upholstery Back Upholstery CoverAdjusting the Back Tension Removing the Adjustable Tension Back Upholstery Installing the Lumbar StrapRemoving the Back Upholstery Cover Removing the Lumbar StrapInstalling the Adjustable Tension Back Upholstery Installing the Back Upholstery CoverDetail a Detail B Back CanesDetail E Removing/Installing Foldover Back Upholstery Installing Foldover Back UpholsteryRemoving Foldover Back Upholstery Front WheelchairBack Height Adjustment HOLE* NumberHole Number Adjustment Pin Back CaneInsert Back Cane Removing/Installing the Back Frame InstallingSeat Replacing Seat UpholsteryChanging Seat Angle/Changing Rear Seat Height Height Adjustment Bar Bottom ViewReplacing/Adjusting the Wheel Locks Adjusting the Wheel LockWheel Locks Replacing the Wheel LockReplacing/Adjusting the Wheel Locks Changing Wheel Lock Handle PositionConfiguration Converting From Pull-to-Lock to Push-to-LockRemoving/Installing Rear Wheels WheelsAdjusting Quick-Release Axles Removing/Installing Rear WheelsReplacing Quad-Release Axles Adjusting Quad-Release HandlesAnd/or Out Removing Play from Rear Wheels Adjusting Quad-Release Handle In and/or OutRemoving Play from Rear Wheels Handrim Replacement Handrim ReplacementAdjusting Wheelbase Length Adjusting Center of Gravity COG Determining Wheelbase LengthWheels Mounting Screws Locknuts Frame Height Adjustment Bar Adjusting Wheelbase Width May be affectedInstalling the Camber Tube Removing/Installing the Camber TubeRemoving the Camber Tube Axle AngleCamber Tube Clamp Adjusting the Camber Tube Detail a Side ViewDetermining/Setting Toe In/Toe Out  For this procedure, refer to on page 76 and FigureTop View of Wheelchair Top View of WheelchairAdjusting Fork Tension CasterDetail a Detail B ONE Standard Fork Sided Fork Removing/Installing/Repositioning the Caster Assemblies Installing Front CasterStandard Forks Removing Front CasterInstalling the Caster Removing/Installing the Fork AssemblyRemoving Fork Assembly One Sided ForkInstalling Fork Assembly  Spacer orientation must be as shown in FigureRepositioning the Front Caster Housings  For this procedure, refer to onSmall Angle Adjustments Caster Housing Angle AdjustmentBelleville Washer Round Adjustment Nut Large Angle Adjustments Interference between Adjusting/Replacing Anti-tipper Anti-TipperAdjusting Anti-tipper Replacing Anti-tipperRelease Buttons Lock ButtonsANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair USA Canada