Invacare 1171880 Repositioning the Front Caster Housings,  For this procedure, refer to on

Page 85

12 CASTER

12.4Repositioning the Front Caster Housings

For this procedure, refer to FIGURE 5 on page 86.

1.Remove the top mounting screw, belleville washer and round adjustment nut and base that secures the caster housing to the front frame.

2.Remove the bottom mounting screw, belleville washer and square adjustment nut that secures the caster housing to the front frame.

Mounting positions for caster housing on the front frame include one mounting screw on the top and one mounting screw on the bottom. The top and bottom mounting screws are ALWAYS aligned vertically and NEVER offset as shown in Detail “A” in FIGURE 5 on page 86.

3.Reposition the caster housing to one of three mounting positions on the front frame.

4.Install the top mounting screw and washer through the front frame and into round adjustment nut and base. Loosely tighten.

5.Install the bottom mounting screw and washer through the front frame and into the square adjustment nut. Loosely tighten.

6.Ensure the caster headtube is perpendicular (90°) to the ground/floor. Refer to Caster Housing Angle Adjustment on page 86.

Part No 1171880

85

Invacare®Top End Reveal™Wheelchair

Page 84 Page 86
Image 85
Page 84 Page 86
Contents InvacareTop End RevealWheelchair Page Contents Seat Caster General SymbolsLimited Warranty General Guidelines SafetyWheelchair User Stability Warning Wheelchair Tie Down RestraintsOperating Information Repair and Service InformationSeat Positioning Straps Weight TrainingTire Pressure and Information Label Locations Serial Number OverviewComponent Identification 0, +4, +8 Typical Product ParametersNon Tapered front end Standard Lock Down, Folding StandardReveal RVL Weight Safety/Handling of Wheelchairs Safety/Handling of WheelchairsStability and Balance SAFETY/HANDLING of Wheelchairs Reaching, Leaning and Bending Forward Lengthening Wheelbase ShorteningReaching, Leaning Bending Forward Backwards Reaching, Leaning BackwardsCoping with Everyday Obstacles Tipping Curbs TippingMoving Up Stairs StairwaysStairways Moving Down StairsTransferring To and From Other Seats EscalatorsSafety Inspection Checklist Safety InspectionInspect Initially Inspect/Adjust Weekly Inspect/Adjust Periodically Inspect/Adjust MonthlySolutions TroubleshootingSuggested Maintenance Procedures Maintenance Maintenance Safety Precautions Tire wear is excessive if Replacing/Repairing Caster Tire/Tube Replacing/Repairing Rear Wheel Tire/TubeAdjusting the Footrest Adjusting/Replacing Standard FootrestFootrest Replacing the Footrest Replacing/Adjusting Optional Adjustable Angle FootrestAdjusting Footplate Depth Adjusting Footplate AngleReplacing/Adjusting Optional Adjustable Angle Footrest Adjustments ClampArms Installing the Swingaway Padded Armrest SocketRemove Back Stop Insert Left Side Armrest Socket Right Side Armrest SocketInstall Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Adjusting Height Installing/Removing/Adjusting the Swingaway Padded ArmrestRemoving Adjusting T-Arm Height  To remove the T-arm, reverse this procedureUnfolding/Folding the Back BackDetail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail When installed Hole in adjustmentThis orientation Square will align withSquare will align with + when installed Hole AdjustmentWith 0 when Seat Rail OrientationBack Upholstery Cover Adjustable Tension Back UpholsteryAdjusting the Back Tension Installing the Lumbar Strap Removing the Adjustable Tension Back UpholsteryRemoving the Back Upholstery Cover Removing the Lumbar StrapInstalling the Back Upholstery Cover Installing the Adjustable Tension Back UpholsteryBack Canes Detail a Detail BDetail E Installing Foldover Back Upholstery Removing/Installing Foldover Back UpholsteryRemoving Foldover Back Upholstery Front WheelchairHOLE* Number Back Height AdjustmentHole Number Adjustment Pin Back CaneInsert Back Cane Installing Removing/Installing the Back FrameReplacing Seat Upholstery SeatChanging Seat Angle/Changing Rear Seat Height Bottom View Height Adjustment BarAdjusting the Wheel Lock Replacing/Adjusting the Wheel LocksWheel Locks Replacing the Wheel LockChanging Wheel Lock Handle Position Replacing/Adjusting the Wheel LocksConverting From Pull-to-Lock to Push-to-Lock ConfigurationWheels Removing/Installing Rear WheelsRemoving/Installing Rear Wheels Adjusting Quick-Release AxlesReplacing Quad-Release Axles Adjusting Quad-Release HandlesAnd/or Out Removing Play from Rear Wheels Adjusting Quad-Release Handle In and/or OutRemoving Play from Rear Wheels Handrim Replacement Handrim ReplacementDetermining Wheelbase Length Adjusting Wheelbase Length Adjusting Center of Gravity COGWheels Mounting Screws Locknuts Frame Height Adjustment Bar May be affected Adjusting Wheelbase WidthInstalling the Camber Tube Removing/Installing the Camber TubeRemoving the Camber Tube Axle AngleCamber Tube Clamp Detail a Side View Adjusting the Camber Tube For this procedure, refer to on page 76 and Figure Determining/Setting Toe In/Toe OutTop View of Wheelchair Top View of WheelchairCaster Adjusting Fork TensionDetail a Detail B ONE Standard Fork Sided Fork Installing Front Caster Removing/Installing/Repositioning the Caster AssembliesStandard Forks Removing Front CasterRemoving/Installing the Fork Assembly Installing the CasterRemoving Fork Assembly One Sided Fork Spacer orientation must be as shown in Figure Installing Fork Assembly For this procedure, refer to on Repositioning the Front Caster HousingsSmall Angle Adjustments Caster Housing Angle AdjustmentBelleville Washer Round Adjustment Nut Large Angle Adjustments Interference between Anti-Tipper Adjusting/Replacing Anti-tipperReplacing Anti-tipper Adjusting Anti-tipperLock Buttons Release ButtonsANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair Canada USA
Top Page Image Contents