Invacare 1171880 user manual Caster Housing Angle Adjustment, Small Angle Adjustments

Page 86

12 CASTER

DETAIL “A” - INSIDE VIEW OF	DETAIL “B” - OUTSIDE VIEW OF
CASTER HOUSING		CASTER HOUSING	Base
Belleville Washer		Round Adjustment Nut
	Front Frame

Top Mounting Screw

Front Frame

Bottom Mounting

Caster Housing

Belleville Washer

Screw

Square Adjustment

Nut

FIGURE 5 Repositioning the Front Caster Housings

12.5Caster Housing Angle Adjustment

For this procedure, refer to FIGURE 6 on page 88.

The round adjustment nuts for smaller (fine tuning) angle adjustments. The square adjustment block is for larger angle adjustments.

Small Angle Adjustments

1.If necessary, loosen the top mounting screw (Detail “A”).

2.Position a large right triangle or “L” square on the ground/floor and against the caster fork (Detail “C”).

Invacare®Top End Reveal™Wheelchair

86

Part No 1171880

Image 86

Contents InvacareTop End RevealWheelchair Page Contents Seat Caster Symbols GeneralLimited Warranty Wheelchair User SafetyGeneral Guidelines Wheelchair Tie Down Restraints Stability WarningRepair and Service Information Operating InformationTire Pressure and Information Weight TrainingSeat Positioning Straps Overview Label Locations Serial NumberComponent Identification Non Tapered front end Standard Typical Product Parameters0, +4, +8 Lock Down, Folding StandardReveal RVL Weight Stability and Balance Safety/Handling of WheelchairsSafety/Handling of Wheelchairs SAFETY/HANDLING of Wheelchairs Lengthening Wheelbase Shortening Reaching, Leaning and Bending ForwardCoping with Everyday Obstacles Reaching, Leaning BackwardsReaching, Leaning Bending Forward Backwards Tipping Tipping CurbsStairways Moving Up StairsMoving Down Stairs StairwaysEscalators Transferring To and From Other SeatsInspect Initially Safety InspectionSafety Inspection Checklist Inspect/Adjust Weekly Inspect/Adjust Monthly Inspect/Adjust PeriodicallyTroubleshooting SolutionsMaintenance Maintenance Safety Precautions Suggested Maintenance Procedures Tire wear is excessive if Replacing/Repairing Rear Wheel Tire/Tube Replacing/Repairing Caster Tire/TubeFootrest Adjusting/Replacing Standard FootrestAdjusting the Footrest Replacing/Adjusting Optional Adjustable Angle Footrest Replacing the FootrestAdjusting Footplate Angle Adjusting Footplate DepthAdjustments Clamp Replacing/Adjusting Optional Adjustable Angle FootrestInstalling the Swingaway Padded Armrest Socket ArmsRemove Back Stop Insert Right Side Armrest Socket Left Side Armrest SocketInstall Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Removing Installing/Removing/Adjusting the Swingaway Padded ArmrestAdjusting Height  To remove the T-arm, reverse this procedure Adjusting T-Arm HeightBack Unfolding/Folding the BackDetail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail This orientation Hole in adjustmentWhen installed Square will align withWith 0 when Hole AdjustmentSquare will align with + when installed Seat Rail OrientationAdjustable Tension Back Upholstery Back Upholstery CoverAdjusting the Back Tension Removing the Back Upholstery Cover Removing the Adjustable Tension Back UpholsteryInstalling the Lumbar Strap Removing the Lumbar StrapInstalling the Adjustable Tension Back Upholstery Installing the Back Upholstery CoverDetail a Detail B Back CanesDetail E Removing Foldover Back Upholstery Removing/Installing Foldover Back UpholsteryInstalling Foldover Back Upholstery Front WheelchairBack Height Adjustment HOLE* NumberInsert Back Cane Adjustment Pin Back CaneHole Number Removing/Installing the Back Frame InstallingSeat Replacing Seat UpholsteryChanging Seat Angle/Changing Rear Seat Height Height Adjustment Bar Bottom ViewWheel Locks Replacing/Adjusting the Wheel LocksAdjusting the Wheel Lock Replacing the Wheel LockReplacing/Adjusting the Wheel Locks Changing Wheel Lock Handle PositionConfiguration Converting From Pull-to-Lock to Push-to-LockRemoving/Installing Rear Wheels WheelsAdjusting Quick-Release Axles Removing/Installing Rear WheelsAnd/or Out Adjusting Quad-Release HandlesReplacing Quad-Release Axles Removing Play from Rear Wheels Adjusting Quad-Release Handle In and/or OutRemoving Play from Rear Wheels Handrim Replacement Handrim ReplacementAdjusting Wheelbase Length Adjusting Center of Gravity COG Determining Wheelbase LengthWheels Mounting Screws Locknuts Frame Height Adjustment Bar Adjusting Wheelbase Width May be affectedRemoving the Camber Tube Removing/Installing the Camber TubeInstalling the Camber Tube Camber Tube Clamp AngleAxle Adjusting the Camber Tube Detail a Side ViewDetermining/Setting Toe In/Toe Out  For this procedure, refer to on page 76 and FigureTop View of Wheelchair Top View of WheelchairAdjusting Fork Tension CasterDetail a Detail B ONE Standard Fork Sided Fork Standard Forks Removing/Installing/Repositioning the Caster AssembliesInstalling Front Caster Removing Front CasterRemoving Fork Assembly Installing the CasterRemoving/Installing the Fork Assembly One Sided ForkInstalling Fork Assembly  Spacer orientation must be as shown in FigureRepositioning the Front Caster Housings  For this procedure, refer to onBelleville Washer Round Adjustment Nut Caster Housing Angle AdjustmentSmall Angle Adjustments Large Angle Adjustments Interference between Adjusting/Replacing Anti-tipper Anti-TipperAdjusting Anti-tipper Replacing Anti-tipperRelease Buttons Lock ButtonsANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair USA Canada