Grandstream Networks 286 user manual Saving the Configuration Changes, Volume, Amplification

Page 33

HandyTone -286 User Manual

Grandstream Networks, Inc.

 

 

 

 

 

 

 

 

 

 

 

 

 

Volume

 

Handset volume adjustment. RX is for receiving volume, TX is for

 

 

Amplification

 

transmission volume. Default

values are 0dB for both parameters. +6dB

 

 

 

 

generates the highest volume and -6dB generates the lowest volume.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Call Progress Tones

 

Using these settings, users can configure various call progress tone frequencies

 

 

 

 

and cadences according to their country standard. By default they are set to

 

 

 

 

North American standard.

 

 

 

 

 

 

Frequencies should be configured with known values to avoid uncomfortable

 

 

 

 

high pitch sounds. ON is the period of ringing (“On time” in ‘ms’) while OFF

 

 

 

 

is the period of silence. In order to set a continuous ring, OFF should be zero.

 

 

 

 

Otherwise it will ring ON ms and a pause of OFF ms and then repeat the

 

 

 

 

pattern. Up to three cadences are supported.

 

 

 

 

 

 

 

 

6.2.4Saving the Configuration Changes

Once a change is made, the user should press the “Update” button in the Configuration Menu. The IP phone will then display the following screen to confirm that the changes have been saved.

Grandstream Device Configuration

STATUS BASIC SETTINGS

ADVANCED SETTINGS

Your configuration changes have been saved.

They will take effect on next reboot.

All Rights Reserved Grandstream Networks, Inc. 2005

Users are recommended to power cycle the HandyTone-286 after seeing the above message.

6.2.5Rebooting the HandyTone-286 from Remote

The administrator of the phone can remotely reboot the phone by pressing the “Reboot” button at the bottom of the configuration menu. Once done, the following screen will be displayed to indicate that rebooting is underway.

33

Image 33
Contents For Firmware Version HandyTone-286 RevTable of Contents Restore Factory Default Setting Grandstream Networks, Inc388 Welcome Installation What is Included in the Package Safety CompliancesWarranty Product Overview Key FeaturesModel HandyTone-286 Hardware SpecificationGet Familiar with Key Pad and Voice Prompt Basic OperationsCalling Phone or Extension Numbers Make Phone CallsCall Hold Direct IP CallsCall Waiting Voice Prompt with option 47, thenCall Transfer Blind TransferAttended Transfer 6 3-way Conferencing Call FeaturesBell style conference Non-bell style conferenceLED Light Pattern Indication FaxRinging Configuration Guide Configuring HandyTone-286 IP through Voice PromptConfiguring HandyTone-286 with Web Browser Registered Yes PPPoE Link Up disabled End User ConfigurationIP Address Product Model HT286 REV Software VersionNAT NAT Mapped Port End User Password Web PortStatistical Status IP Address Time ZoneUpdate Dhcp hostname PPPoE passwordDhcp domain Dhcp vendor classAdvanced User Configuration Dial Plan Prefix Use Bell-style Yes if Yes, *23 will be disabled Override MTU Size SIP Server AuthenticateHome NPA Preferred VocoderG723 Rate Fax ModeILBC frame size ILBC payload typeTimeout RebootUser ID is phone NumberMWI Caller ID Scheme Special FeaturesOnhook Voltage Polarity ReversalSession Expiration TimerMin-SE Caller RequestFirmware Upgrade Force TimerPath Config Server Path Postfix Config File PrefixRebooting the HandyTone-286 from Remote Saving the Configuration ChangesVolume AmplificationClick to relogin Configuration through a Central ServerFirmware Upgrade through TFTP/HTTP Software Upgrade with TftpConfiguration File Download Firmware and Configuration File Prefix and PostfixManaging Firmware and Configuration File Download Step Restore Factory Default SettingGlossary of Terms Did DNSDSP DtmfFXS Echo CancellationDhcp 323IVR IP-PBXMTU NTPRtcp PstnRTP SDPUDP TftpVAD Vlan