Siemens Gigaset 2010 operating instructions Certification and CE marking

Page 8

14.8.98

KAP01.FM5

Gigaset 2010, UEB/engl.: A30852-X1100-E301-3-7619

Certification and CE marking

Siemens Gigasetâ 2010 was certified according to EU guideline 91/263/EEC (CTR 6, CTR 10). Anyone is per- mitted to connect this telephone to a telephone jack and use it.

This telephone fulfils the requirements of the following

EU guidelines:

89/336/EEC	“Electromagnetic compatibility”
73/23/EEC	“Electrical resources used within
	specific voltage ranges”

The CE marking confirms the telephone is in compliance with the above-mentioned guidelines (CE 0188 X)

A4

A4

Image 8

Contents Gigaset Gigaset WegweiserOverview Gigaset Keys on the Gigaset 1000S mobile unit Overview KeysKeys on the base station Display symbols bottom line Overview Key functions and display symbolsDisplay Symbols top line Overview Meaning of symbols Safety precautions Certification and CE marking Contents Contents Observe the safety precautions Check the contents of the packageStepwise startup Stepwise startupPhone cord Stepwise startup Connecting the base stationPower cord Stepwise startup Inserting the batteries into the handset Charging the batteriesSetting the phone to dial pulsing DP Stepwise startup Check signaling methodChecking your own telephone’s signalling method Temperature/ambient conditions Installing the base stationInstallation site/installation area For users who wear hearing aids NiMH rechargeable Batteries 1100 mAh Mounting the carrying clip onto the handset Maintenance notesConnecting the telephone socket Technical data GfskWarranty Third party use/disposalProcedure in the case of malfunctions Symptom Cause RemedyWith telephone systems Exchange code not entered Overview Signal tones Switching the handset to protected mode Operating modesOperating modes ON/OFF/PROTECTED modesWhen the handset is switched off Switching on the handsetSetting the signaling method Operating modes Signaling methodChecking the signaling method of your telephone line O037 B Possible signaling method settingsOperating modes Operating in a telephone system Operating modes Exchange codes Entering the exchange code024B 025B 020B 021B Changing the system code, changing the PINModify the pause length according to the excharge code Deleting the exchange codeResetting the base station to factory defaults B89250B Changing the system codeKAP04.FM5 Incoming calls Incoming callsAccepting calls If the handset is in the charging unitBR or Switching off the microphone mute functionEnding an internal call External outgoing calls External outgoing callsCalling external subscribers FN b FNo answer or line busy External outgoing calls RedialManually inserting a pause Repeating the last number dialedDialing speed dial numbers Dialing with speed dial numbers and number checkDialing a DSS number from a locked handset Ending a callCollective ringing and internal calls Collective ringing and internal callsFN b G End call prematurelynDisconnect internal party again Consultation calls Internal consultation calls and transferring callsInternal consultation calls and transferring calls Either FN b Base station settingsBase station settings Base station settings Setting the base station ringer tone Switching music-on-hold on/offIndividual settings on the Gigaset 2000S mobile unit Individual settings on the Gigaset 2000S mobile unitSetting the ringer volume Setting the ringer toneVolume Activating/deactivating notification and warning tonesB31 Activating/deactivating the key confirmation toneB34 B37B32 B33Activating/deactivating the synchronization tone B35Activating/deactivating automatic call acceptance B38 Checking or store speed dial numbers Clearing all speed dial numbers O96 Activating/deactivating the call duration displayActivating/deactivating the call duration display Emergency calls when the Gigaset 2010 is locked 1B Switch on the lock. or 0B Switch off the lockGigaset 2010 lock functions Gigaset 2010 lock functionsDeleting all emergency numbers #25Displaying and storing emergency numbers Displaying or storing barred numbers Gigaset 2010 lock functions Barred numbers for handsetsFN b Activating/deactivating the call number lock Deleting all barred numbersSet Unrestricted trunk access Lock functions on the handset Lock functions on the handsetActivating/deactivating the handset lock B81 B80 DSS number for handset lockDisplay or store a DSS number Deleting a DSS numberB F H Display with locked handsetDisplay with system lock Display with call number lockRegister the handset Registering a Gigaset 2000S handset at a base stationPrepare the base station De-registering a handset from a base station Switching between collective ringing and ring priority Operating more than one handsetOperating more than one handset Ring priority for incoming callsSetting the number of rings for ring priority Selecting a handset for ring priorityOperation at more than one base station Procedure for operating at more than one base stationOperation at more than one base station Setting the preferred station Selecting the best stationPfN With Gigaset 2000S handsetYou can reset the handset to the factory default Quick reference guide handset Gigaset 2000S Quick reference guide handset Gigaset 2000SIndex IndexGIGA2010.SIX Ringer KAP21.FM5