Multi-Link ML-100, ML-001 manual Operation, Advanced Programming, Alert Mode, Erase Sensors

Page 20

OPERATION

The Control Panel is always in one of the 2 operating modes:

1.Alert Mode - When the system is not armed (ARM LED off), it is in alert mode.

2.Alarm Mode - When the system is armed (ARM LED on), it is in alarm mode.

Alert Mode

The Control Panel will be in alert mode automatically if the system is not armed. Alert mode allows users inside the premises to know what sensor is triggered. It is intended to be used when someone stays inside the premises.

In alert mode, the control panel will give you notification of the triggered sensor(s) by voice announcement, unique beeping and LED flashing.

1

Number of beeps

Zone of the triggered sensor

2

Number of flashes of zone LED

Sensor number of the triggered sensor

Note:

-Each zone can program up to 2 sensors. There are 5 zones, so up to 10 sensors can be programmed to the control panel. Please refer to page 37, "Sensor Location Selection Guide" for detail information.

Alert Mode Examples (Door/Window sensor sold separately)

Zone 1 Sensor 1 1.

2. Single flash

Beep___Beep___

 

Beep___Beep

 

Zone 3 Sensor 2 window

1.

2. Double flash

open

Beep Beep Beep___

 

 

 

 

Beep Beep Beep___

 

Note:

-For Door / Window sensor, alert notification (beeping and LED flashing) will continue until the sensor is in closed position, i.e. closing the window or door.

-For motion sensor, the alert notification was disabled at the factory default. To perform the walk test, it requires to enable the Alert Zone (Bypass Zone) feature in the Control Panel. After the walk test, it needs to disable this alert zone feature otherwise it will bypass the signal in the alarm mode. Please refer to the page 33, "Alert Zone" for detail. Please refer to information.

–18–

ADVANCED PROGRAMMING

 

SENSOR 1

SENSOR 2

This row

:

 

Buttons for

 

 

 

Zone 1

Button [1]

Button [6]

Sensor 1

 

Zone 2

Button [2]

Button [7]

Zone LED :

Flash once

 

 

 

Zone 3

Button [3]

Button [8]

 

 

Zone 4

Button [4]

Button [9]

 

 

Zone 5

Button [5]

Button [0]

This row

:

 

 

 

Buttons for

 

 

 

Sensor 2

 

 

 

 

Zone LED :

 

 

 

Flash twice

Erase Sensors

Proceed to the following to erase a sensor.

Step

 

Keys

 

Function

Description

Note

 

 

 

 

 

 

 

1

 

[PROG]

 

Enter

Enter master

3 beeps for valid password.

 

 

[MPIN]

 

Programming

password to

1 long beep for invalid

 

 

 

 

mode

programming mode

password.

 

 

 

 

 

 

 

2

 

[9]

 

Select erase

 

After [9] is entered, some

 

 

 

 

remote

 

zone LEDs will flash or

 

 

 

 

programming

 

stay off. The zone LEDs

 

 

 

 

 

 

represent whether that zone

 

 

 

 

 

 

is occupied by any sensor.

 

 

 

 

 

 

**See Table D below.

3

 

To erase an

Select the

Refer to the table

After you have selected the

 

 

occupied

 

sensor you

below to select the

sensor, you will hear 3 beeps

 

 

sensor, press

would like to

remote location.

and verbal confirmation

 

 

[1] to [0].

 

erase

 

[Zone X Sensor Y Empty

 

 

 

 

 

 

Memory], where X and Y

 

 

 

 

 

 

are the zone and sensor

 

 

 

 

 

 

numbers you have selected.

 

 

 

 

 

 

 

 

 

 

 

 

ZONE LED

 

DESCRIPTION

 

 

 

 

 

 

Off

 

Zone is not occupied by any sensor

 

 

 

 

Flashes once

This zone is occupied by sensor 1.

 

 

 

 

Flashes twice

This zone is occupied by sensor 2.

 

 

 

Flashes once,

This zone is occupied by sensors 1 and 2.

then twice

 

 

 

 

 

 

 

 

 

 

 

 

**Table D: Zone LED status for erasing sensors.

–39–

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Email support@skylinkhome.com Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Tel 905Fax 905 Home Smart Center Important Safety Instructions Declaration of Conformity EMCContent System ConfigurationOperation Disarming a triggered control panelFCC Information Consumer Information IntroductionOverview System Configuration Introduction Accessories Control Module SW-100Control Module SW-101U UK, SW-101F French, SW-101G German Emergency Dialer AD-433SInstallation Installing the ConsoleDoor/Window Sensor WD-101 Repeater RP-434Water Sensor FS-101 Garage Door MonitorTM Sensor GS-101Trouble Shooting Programming PasswordsChanging Passwords Order to change the password, follow the procedures belowControl Panel Questions SolutionsPhone Number Programming Testing Phone Numbers Home AutomationContact ID Phone number Event TriggerAccount Number Programming Zone LED DescriptionErase Control Modules Deactivating the Digital DialerOperation Installing Door / Window Sensors Part 2 Learn signal from Control Panel to Control ModuleTesting Mounting the SensorInstalling Motion Sensor Insert BatteryPart 1 Learn signal from Control Module to Control Panel Table E Zone LED status for learning control moduleLearn Control Modules To indicate the light has been turned onAlert Mode OperationAdvanced Programming Erase SensorsTable C MuteLearn Sensors Continue Learn Sensors System StatusArming the System Erase Keychain / Keypad Remotes Disarming the systemLearn Keychain / Keypad Remotes Disarming a triggered control panelDisarming under Duress To enable alert zone feature, follow the instructions below PanicSystem Failure Phone Line FailureLow Battery It is recommend to enable alert zone ifSensor Failure Control PanelTo enable auto mute feature, follow the instructions below Auto MuteExample CommunicationReceiving the Emergency Call To access the control panel away from home Calling in when you are away from homeSystem Armed Alarm Mode Remote Operation by TelephoneRemote Phone Operations Beep / AlarmSystem Disarmed Alert Mode
Top Page Image Contents