Disarming a triggered control panel

OPERATION

2.You must enter a valid password, either the Master Password, or Secondary Password to disarm the system before entry delay expires.

3.When a valid password is entered, you will hear “System Disarmed” and the entry delay beeping will stop, the ARM LED will be off.

Note:

-The control panel can also be disarmed remotely when nobody is home, with a touch tone phone. Please refer to “Remote Operation by Telephone” on page 27.

-If 3 consecutive incorrect passwords are entered, alarm will sound immediately, the control panel will be in panic mode, and start calling the emergency phone numbers.

If "System Panic" is announced from the control panel after it has been disarmed, that means the alarm was triggered when it was in armed mode. Follow the procedures below to set the control panel back to standby mode.

1.If the alarm was caused by sensor(s), there will be flashing LEDs and beeping indicating which sensor(s) triggered the alarm. You may want to check the condition of the triggered sensor(s), the sensor(s) may be damaged if there were break-ins.

2.You need to reset the sensor manually by triggering it twice, i.e. open and then close a door / window sensor, or walk in front of the motion sensor. The LED representing that sensor will stop flashing after it receives the signal from the sensor.

3.You must now enter the password again on the control panel or press the disarm button on the keychain remote, as an acknowledgement of the alarm event. This will set the control panel back to standby mode.

Disarming under Duress

If you are forcibly compelled to disarm the control panel, you may enter the Duress Password. Entering the duress password will terminate the entry delay, i.e. no more entry delay beeping. But the control panel will silently call the emergency phone numbers for help. The called party will hear the voice announcement “System Panic”.

Note:

- The default duress password is [3838].

–22–

ADVANCED PROGRAMMING

Learn Keychain / Keypad Remotes

Additional keychain or keypad remotes can be programmed to the control panel. Maximum of 5 keychain/keypad remotes can be programmed to the control panel.

-Keychain or keypad remotes should be programmed to Device 6 to Device 0.

Follow the instructions below to program remote(s) to remote location(s) 6, 7, 8, 9, or 0, which is the bottom row of the numeric keypad of the control panel.

Step	Keys		Function	Description	Note

1	[PROG]		Enter Program-	Enter master	3 beeps for valid
	[MPIN]		ming mode	password to	password. 1 long beep
				programming mode	for invalid password.
2	[4]		Select learn		After [4] is entered, some
			remote		zone LEDs will flash or
			programming		stay off. The zone LEDs
					represent whether that
					zone is already occupied
					by another remote.
					** See Table A below.

3	[6] to [0]		Select remote	Select a remote	After you have selected
			location	location [6], [7],	the remote location, that
			(Max. 5 remotes)	[8], [9] or [0].	zone LED will be on.

4	Activate the		Trigger remote	Once the signal is	You will hear
	remote by			transmitted to the	[Device X Accepted],
	pressing any			Control Panel, that	where “X” is the remote
	one of the			signal which will	location.
	buttons.			be stored.


ZONE LED		DESCRIPTION

Off		Zone is not occupied by any remote

Flashes twice		This zone is occupied by another remote. Programming another
		remote to this zone will overwrite the previous remote.

Flashes once		This zone is occupied by a control module* (Optional).
		You can still program a remote to this zone, and it will not overwrite
		the control module* you have in this zone. (Refer to page 40 Home
		Automation for more information)

Flashes once,		This zone is occupied by a remote AND a control module*.
then twice		If you program another remote to this zone, it will overwrite the
		previous remote, but not the control module*.

**Table A: Zone LED status for learning keychain/keypad remote(s).

*Please refer to learn control module on page 40.

–35–

OPERATION