Telular Phonecell SX4D Technician Commands, Enter Dial Tone After Remote Call Terminate Option

Page 33

Phonecell SX4D Programming - continued

IMPORTANT!

The following commands may be used by a trained service technician to change the configuration of the Phonecell SX4D. WARNING: these commands are

!intended for use by trained service technicians only. Untrained users could damage the Phonecell SX4D, violate local regulations and breach the service agreement with the cellular provider. For further assistance, please contact your Authorized Telular Representative.

Phonecell SX4D Technician Commands

The following commands are to used by trained field technicians to set up the Phonecell SX4D for operation in the network. Since these commands can directly affect the proper operation of the unit, there is an additional level of security to prevent casual access.

While in the User Programming mode, the technician presses the flash and redial keys simultaneously. A "PASSWORD" label will be displayed on the alpha row. The technician enters the password. As the password digits are entered from the keypad, only the center segment of the dialed digits row will illuminate. Note that as an exception to entry rule #4, the NEW icon will not illuminate, since the pass- word data is not being changed. When the technician presses the Redial key, the password is processed. If the password is correct, the "DTRCT" label is displayed on the alpha row. If not, the incorrect entry rule #7 will be followed, except that the NEW icon will not be illuminated. If the user fails to enter the correct password after three tries, the programming mode is exited without flashing the dialed digit row.

The following commands are displayed when the technician enters the program- ming mode. In the following sections, an <entered value> is comprised of the dig- its 0 through 9.

Enter Dial Tone After Remote Call Terminate Option

The following key sequence is used to enter the dial tone after remote call terminate option:

Label: DTRCT

Data: <dial tone option>

The dial tone value is set to 0 for no tone after a remote on-hook; 1 to enable dial tone after remote on hook. If the value is neither 0 nor 1, it is considered invalid. The factory default is 1.

Enter Post Receiver Off-Hook Option

The following key sequence is used to enter the post receiver off-hook option:

Label: POST ROH

Data: <post ROH option>

The post ROH value is set to 0 for continuous ROH tone; 1 to disable ROH tone and periodically check for an on-hook condition. If the post ROH value is neither 0 nor 1, it is considered invalid. The factory default is 1.

SX4D GSM 900 • SX4D GSM 1800

32

USER MANUAL

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Phonecell SX4D GSM Phonecell SX4D GSM Introduction Power SupplyTel 847-247-9400 · Fax Please see Pages 7 and 8 for ImportantTable of Contents Temperature Environment Safety InformationExposure to RF Radio Frequency Energy Safe Operation RequirementSafety Information Potentially Explosive Atmospheres FCC Part 15 Class B ComplianceGSM Type Acceptance Terms and Conditions for USE of Phonecell Products Product Important NoticesImportant Notices IV. What this Warranty does not CoverPre-Installation Checklist Getting StartedUn-Packing Your Phonecell SX4D Installation Summary AC PowerOtherwise, continue to Step Optional Yagi Antenna SetupEmergency Battery Backup Connect Phonecell SX4D to AC PowerPower ReceptacleHow to Install the Mini-SIM Card SIM Card Installation and SetupSIM PIN Programming Press 4-digit SIM number #Press * * 04 * oldPIN * new PIN * new PIN # How to Unblock a SIM PIN Enter Automatic PIN Entry OptionEnter PIN For Automatic PIN Entry Determine Phonecell SX4D Location 83 mm 3-1/4 inches Mounting Battery Hooks Access Door Optional Wall-Mount InstallationWall-Mount Instructions Mounting Clip Cradle tab upLCD Display Phonecell SX4D OperationDialed Digits AlphaPhonecell SX4D Normal Mode Phonecell SX4D Normal Power ModeCall-Timer Phonecell SX4D OperationAlpha Bottom Row Dialed Digits Middle RowCellular Service Indicator In-Use IndicatorIn-Use Indicator Received Signal Strength Cellular Service Indicator Alpha RowPhonecell SX4D Controls Phonecell OperationFront Panel Back PanelHow to Receive a Call How to Place a CallHow to End a Call Hookflash FunctionZero Dial Delay for Frequently Called Numbers Variable Dial Time Auto Send Delay OptionUsing Standard Supplementary Services Mobile Equipment Personalization MEPTeleservice DelayCall Forwarding Unconditional Call Forwarding on No Reply Register * 31 # Call Phone Number SendRegister # 31 # Call Phone Number Send Barring of All Outgoing Calls All Incoming Call Barring Phonecell SX4D Troubleshooting Programming Mode Phonecell SX4D Programming Mode OverviewEnter Programming Mode Programming Mode OverviewPhonecell SX4D Programming Phonecell SX4D User-Programming CommandsEnter Dial Tone After Remote Call Terminate Option Phonecell SX4D Technician CommandsEnter Post Receiver Off-Hook Option Label Dtrct Data dial tone optionEnter Periodic Self Test Time Option Enter In-Call Dtmf Signaling OptionEnter Dial Tone Type Selection Option Enter Mobile Equipment Personalization for SIMEnter Mobile Equipment Personalization for Network Subset Enter Mobile Equipment Personalization for Service ProviderEnter Mobile Equipment Personalization for Corporate Enter Voicemail Retrieval Digit StringTelular Corporation
Top Page Image Contents