Telular SX4D Safety Information, Exposure to RF Radio Frequency Energy, Temperature Environment

Page 5

Safety Information

IMPORTANT!

To ensure safe and efficient operation, please read the following information and observe these guidelines whenever using your Phonecell SX4D.

Your Phonecell SX4D GSM 900 and SX4D GSM 1800 Desktop Phones function as both a radio transmitter and receiver. When it is ON, the Desktop Phone receives and sends out radio frequency (RF) energy. The GSM 900 unit operates in the frequency range between 890 and 960 MHz, and the GSM 1800 between 1710 MHz and 1880 MHz. Both employ commonly used phase/frequency modulation techniques. When you use your Phonecell SX4D Desktop Phone, the cellular system handling your call controls the power level at which your unit transmits. Nominal power output for the GSM 900 unit is 2 watts and for the GSM 1800 unit is 1 watt.

Exposure to RF (Radio Frequency) Energy

In 1991, the Institute of Electrical and Electronics Engineers (IEEE), and in 1992, the American National Standards Institute (ANSI), updated the 1982 ANSI Standard for safety levels with respect to human exposure to RF energy. After reviewing the available body of research, more than 120 scientists, engineers and physicians from universities, government health agencies and industry developed this updated Standard. In March, 1993, the U.S. Federal Communications Commission (FCC) proposed the adoption of this updated Standard.

The design of your Telular Phonecell SX4D complies with this updated Standard. Of course, if you want to limit RF exposure even further than the updated ANSI Standard, you may choose to control the duration of your calls and operate your phone in the most power-efficient manner.

Safe Operation Requirement

Do not operate your Phonecell SX4D when any person is within 1 inch (2,5 cm) of the antenna.

Temperature Environment

Operating Temperature: From -10°C (14°F) to +50°C (122°F);

Up to 95% relative humidity (non-condensing)

Storage Temperature: From -20°C (-4°F) to +60°C (140°F);

Up to 95% relative humidity (non-condensing)

WARNING!

!Your Phonecell SX4D must be placed or mounted on a flat surface to allow proper ventilation. Do not block the air vents or the space beneath your Phonecell SX4D as this could cause the unit to overheat and fail.

SX4D GSM 900 • SX4D GSM 1800

4

USER MANUAL

Image 5
Contents Phonecell SX4D GSM Phonecell SX4D GSM Introduction Power SupplyTel 847-247-9400 · Fax Please see Pages 7 and 8 for ImportantTable of Contents Temperature Environment Safety InformationExposure to RF Radio Frequency Energy Safe Operation RequirementSafety Information GSM Type Acceptance Potentially Explosive AtmospheresFCC Part 15 Class B Compliance Terms and Conditions for USE of Phonecell Products Product Important NoticesImportant Notices IV. What this Warranty does not CoverUn-Packing Your Phonecell SX4D Pre-Installation ChecklistGetting Started Otherwise, continue to Step Installation SummaryAC Power Optional Yagi Antenna SetupEmergency Battery Backup Connect Phonecell SX4D to AC PowerPower ReceptacleHow to Install the Mini-SIM Card SIM Card Installation and SetupPress * * 04 * oldPIN * new PIN * new PIN # SIM PIN ProgrammingPress 4-digit SIM number # Enter PIN For Automatic PIN Entry How to Unblock a SIM PINEnter Automatic PIN Entry Option Determine Phonecell SX4D Location 83 mm 3-1/4 inches Mounting Battery Hooks Access Door Optional Wall-Mount InstallationWall-Mount Instructions Mounting Clip Cradle tab upLCD Display Phonecell SX4D OperationDialed Digits AlphaPhonecell SX4D Normal Mode Phonecell SX4D Normal Power ModeCall-Timer Phonecell SX4D OperationAlpha Bottom Row Dialed Digits Middle RowCellular Service Indicator In-Use IndicatorIn-Use Indicator Received Signal Strength Cellular Service Indicator Alpha RowPhonecell SX4D Controls Phonecell OperationFront Panel Back PanelHow to Receive a Call How to Place a CallHow to End a Call Hookflash FunctionZero Dial Delay for Frequently Called Numbers Variable Dial Time Auto Send Delay OptionUsing Standard Supplementary Services Mobile Equipment Personalization MEPCall Forwarding Unconditional TeleserviceDelay Register # 31 # Call Phone Number Send Call Forwarding on No ReplyRegister * 31 # Call Phone Number Send Barring of All Outgoing Calls All Incoming Call Barring Phonecell SX4D Troubleshooting Programming Mode Phonecell SX4D Programming Mode OverviewEnter Programming Mode Programming Mode OverviewPhonecell SX4D Programming Phonecell SX4D User-Programming CommandsEnter Dial Tone After Remote Call Terminate Option Phonecell SX4D Technician CommandsEnter Post Receiver Off-Hook Option Label Dtrct Data dial tone optionEnter Periodic Self Test Time Option Enter In-Call Dtmf Signaling OptionEnter Dial Tone Type Selection Option Enter Mobile Equipment Personalization for SIMEnter Mobile Equipment Personalization for Network Subset Enter Mobile Equipment Personalization for Service ProviderEnter Mobile Equipment Personalization for Corporate Enter Voicemail Retrieval Digit StringTelular Corporation