Motorola XTNi Series Charging the Battery, Charging with the Drop-in Tray Single Unit Charger

Page 21

Battery Meter

The battery meter located in the upper left corner of the display indicates how much battery power you have remaining.

XTNi™ Series Battery Meter

 

3 Bars

2 Bars

1 Bar

 

Battery

Type

Li-Ion100%-70% 70%-30% 30%-0%

AA100%-70% 70%-30% 30%-0%

Charging the Battery

To charge the battery (with the radio attached), place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi-Unit Charger.

Charging with the Drop-in Tray Single Unit Charger

Power Supply (Transformer)

Drop-in Tray

Charger Port

1.Place the drop-in tray charger on a flat surface.

2.Insert the connector of the power supply into the port on the side of the drop-in tray charger.

3.Plug the AC adaptor into a power outlet.

4.Insert the radio into the tray with the front of the radio facing the front of the charger, as shown.

Note: When charging a battery attached to a radio, turn the radio OFF to ensure a full charge. See “Operational Safety Guidelines” on page 7 for more information.

BATTERIES AND CHARGERS

19English

Image 21
Contents Page Page Contents Getting Started Programming FeaturesContents AccessoriesComputer Software Copyrights Computer Software CopyrightsSafety SafetyBatteries and Chargers Safety Information Batteries and Chargers Safety InformationOperational Safety Guidelines Radio Overview Parts of the RadioRadio Radio Overview Side Buttons Lithium-Ion Li-Ion BatteryModel Frequency Transmit Power Number Antenna Band About the Li-Ion Battery Battery Features and Charging OptionsBatteries and Chargers Batteries and ChargersBattery Recycling and Disposal Battery Latchbattery latch Slots Turn OFF the radio Batteries and Chargers Power Supply, Adaptors and Drop-in Tray Charger Install RemoveBattery Life Information Installing Spring Action Belt ClipFollowing chart summarizes battery life estimations Charging with the Drop-in Tray Single Unit Charger Charging the BatteryCharging a Stand-Alone Battery Charging a Standard Battery Adjustable bracket Standard High and Ultra High Capacity Charging a High Capacity Battery Standard Charger LED Indicator Drop-in Tray Charger LED IndicatorsEstimated Charging Time MUC LED Indicator Getting Started Adjusting VolumeGetting Started Turning Radio ON/OFFSelecting a Channel Talking and MonitoringReceiving a Call Talk Range Signal Strength Indicator and Channel Busy IndicatorsGetting Started Radio Status LED Indication Getting Started Radio LED IndicatorsHANDS-FREE USE/VOX With Compatible VOX AccessoriesHands Free without Accessories iVOX Battery SaveReset To Factory Defaults End of Transmission Tone Roger Beep Tone Setting VOX/iVOX SensitivityKeypad Beeps Menu OptionsIVO Setting VOX / iVOX sensitivityStarted GettingImic YES Entering Programming Mode Programming FeaturesProgramming Features Programming RX Reception FrequenciesProgramming RX Reception Codes CTCSS/DPL Programming RX Reception Bandwidth RX BWProgramming Maximum Number of Channels Programming Scramble LProgramming Call Tones MA X CHProgramming Microphone Gain Level Programming Scan List YESProgramming Buttons Editing Channel Alias Name Nuisance Channel Delete Time-Out Timer CPS Computer Programming SoftwareBandwidth Select Battery Type Setting Call TonesScramble Cloning with a Multi-Unit Charger MUC Programming Features Cloning RadiosTurn on the Target radio and place it Into one of the SUCs What to do if cloning fails Cloning Radios using the CPS Computer Programming Software Troubleshooting TroubleshootingDoes not come on Cannot activate VOX USE and Care If the radio is submerged in waterUSE and Care Frequency and Code Charts Frequency and Code ChartsChannel Radios PMR 446 Defaults Ctcss DPL Codes 108 627 115 712 Warranty Information WarrantyWhat is not Covered by the Warranty Motorola LimitedMotorola Limited Warranty Accessories Chargers Page 6871663M05