Motorola XTNi Series manual Ivo, Setting VOX / iVOX sensitivity

Page 36

GETTING STARTED

long press the PTT button to save and exit or

turn OFF radio to exit without saving changes.

When there is no activity for more than ten seconds, MENU mode will time out.

Setting VOX / iVOX sensitivity

The VOX/iVOX sensitivity can be adjusted via the MENU as well as the CPS. To modify via the MENU, first make sure you have enabled either VOX or iVOX. (See page 31). Once VOX/iVOX has been enabled, short press MENU.

If you have iVOX enabled and press MENU, your radio will display the following:

IVOX

If you have VOX enabled (with accessory connected) and press MENU, your radio will display the following:

IVOX

To change the sensitivity level, use the

 

/

 

 

buttons:

 

 

0 = OFF (For VOX accessories only)

1 = Low sensitivity (suitable for noisy environments)

2 = Medium sensitivity

3 = High sensitivity (suitable for quiet environments)

Once you have selected the value you want, press MENU again to go to the next step or turn OFF radio to exit without saving changes.

English 34

Image 36
Contents Page Page Contents Programming Features Getting StartedAccessories ContentsComputer Software Copyrights Computer Software CopyrightsSafety SafetyBatteries and Chargers Safety Information Batteries and Chargers Safety InformationOperational Safety Guidelines Radio Overview Parts of the RadioRadio Radio Overview Lithium-Ion Li-Ion Battery Side ButtonsModel Frequency Transmit Power Number Antenna Band Battery Features and Charging Options About the Li-Ion BatteryBatteries and Chargers Batteries and ChargersBattery Recycling and Disposal Battery Latchbattery latch Slots Turn OFF the radio Batteries and Chargers Install Remove Power Supply, Adaptors and Drop-in Tray ChargerInstalling Spring Action Belt Clip Battery Life InformationFollowing chart summarizes battery life estimations Charging the Battery Charging with the Drop-in Tray Single Unit ChargerCharging a Stand-Alone Battery Charging a Standard Battery Adjustable bracket Standard High and Ultra High Capacity Charging a High Capacity Battery Drop-in Tray Charger LED Indicators Standard Charger LED IndicatorEstimated Charging Time MUC LED Indicator Adjusting Volume Getting StartedGetting Started Turning Radio ON/OFFSelecting a Channel Talking and MonitoringReceiving a Call Signal Strength Indicator and Channel Busy Indicators Talk RangeGetting Started Getting Started Radio LED Indicators Radio Status LED IndicationWith Compatible VOX Accessories HANDS-FREE USE/VOXHands Free without Accessories iVOX Battery SaveReset To Factory Defaults Setting VOX/iVOX Sensitivity End of Transmission Tone Roger Beep ToneKeypad Beeps Menu OptionsSetting VOX / iVOX sensitivity IVOGetting StartedImic YES Programming Features Entering Programming ModeProgramming Features Programming RX Reception FrequenciesProgramming RX Reception Codes CTCSS/DPL RX BW Programming RX Reception BandwidthProgramming Scramble L Programming Maximum Number of ChannelsMA X CH Programming Call TonesProgramming Microphone Gain Level YES Programming Scan ListProgramming Buttons Editing Channel Alias Name Nuisance Channel Delete Time-Out Timer CPS Computer Programming SoftwareBandwidth Select Battery Type Setting Call TonesScramble Programming Features Cloning Radios Cloning with a Multi-Unit Charger MUCTurn on the Target radio and place it Into one of the SUCs What to do if cloning fails Cloning Radios using the CPS Computer Programming Software Troubleshooting TroubleshootingDoes not come on Cannot activate VOX USE and Care If the radio is submerged in waterUSE and Care Frequency and Code Charts Frequency and Code ChartsChannel Radios PMR 446 Defaults Ctcss DPL Codes 108 627 115 712 Warranty Warranty InformationWhat is not Covered by the Warranty Motorola LimitedMotorola Limited Warranty Accessories Chargers Page 6871663M05