Motorola XTNi Series manual Rx Bw, Programming RX Reception Bandwidth

Page 42

MENU to scroll through the options until you reach the ‘Code Programming Mode’. The radio display will show the blinking CTCSS/ DPL code as follows:.

MENU to scroll through the options until you reach the ‘Bandwidth Programming Mode’. The radio display will show the current bandwidth setting as follows:

PROGRAMMING FEATURES

RX

To program the desired code, scroll up/down

with the / buttons until you get the CTCSS/DPL code value you want to set up. Long press the PTT button to exit and save.

PROGRAMMING RX (RECEPTION) BANDWIDTH

Some frequencies have selectable channel spacing, which must match other radios for optimum audio quality.

Once you have chosen the channel you want to program, short press the PTT button or

RX BW

To program the desired bandwidth (HI =

25Khz, LOW = 12.5 Khz), use the / buttons until to select the value. Long press the PTT button to exit and save or short press the PTT button to move to the next programming feature without saving.

Note: If the value of the bandwidth cannot be changed, the display setting remain solid.

English 40

Image 42
Contents Page Page Contents Programming Features Getting StartedAccessories ContentsComputer Software Copyrights Computer Software CopyrightsSafety SafetyBatteries and Chargers Safety Information Batteries and Chargers Safety InformationOperational Safety Guidelines Radio Overview Parts of the RadioRadio Radio Overview Lithium-Ion Li-Ion Battery Side ButtonsModel Frequency Transmit Power Number Antenna Band Batteries and Chargers Battery Features and Charging OptionsAbout the Li-Ion Battery Batteries and ChargersBattery Recycling and Disposal Battery Latchbattery latch Slots Turn OFF the radio Batteries and Chargers Install Remove Power Supply, Adaptors and Drop-in Tray ChargerInstalling Spring Action Belt Clip Battery Life InformationFollowing chart summarizes battery life estimations Charging the Battery Charging with the Drop-in Tray Single Unit ChargerCharging a Stand-Alone Battery Charging a Standard Battery Adjustable bracket Standard High and Ultra High Capacity Charging a High Capacity Battery Drop-in Tray Charger LED Indicators Standard Charger LED IndicatorEstimated Charging Time MUC LED Indicator Getting Started Adjusting VolumeGetting Started Turning Radio ON/OFFSelecting a Channel Talking and MonitoringReceiving a Call Signal Strength Indicator and Channel Busy Indicators Talk RangeGetting Started Getting Started Radio LED Indicators Radio Status LED IndicationWith Compatible VOX Accessories HANDS-FREE USE/VOXHands Free without Accessories iVOX Battery SaveReset To Factory Defaults Keypad Beeps Setting VOX/iVOX SensitivityEnd of Transmission Tone Roger Beep Tone Menu OptionsSetting VOX / iVOX sensitivity IVOGetting StartedImic YES Programming Features Entering Programming ModeProgramming Features Programming RX Reception FrequenciesProgramming RX Reception Codes CTCSS/DPL RX BW Programming RX Reception BandwidthProgramming Scramble L Programming Maximum Number of ChannelsMA X CH Programming Call TonesProgramming Microphone Gain Level YES Programming Scan ListProgramming Buttons Editing Channel Alias Name Nuisance Channel Delete Time-Out Timer CPS Computer Programming SoftwareBandwidth Select Battery Type Setting Call TonesScramble Programming Features Cloning Radios Cloning with a Multi-Unit Charger MUCTurn on the Target radio and place it Into one of the SUCs What to do if cloning fails Cloning Radios using the CPS Computer Programming Software Troubleshooting TroubleshootingDoes not come on Cannot activate VOX USE and Care If the radio is submerged in waterUSE and Care Frequency and Code Charts Frequency and Code ChartsChannel Radios PMR 446 Defaults Ctcss DPL Codes 108 627 115 712 What is not Covered by the Warranty WarrantyWarranty Information Motorola LimitedMotorola Limited Warranty Accessories Chargers Page 6871663M05