VTech VT 2960 Basic Operation, Base Unit Paging Handset, Handset Paging Base Unit

Page 23

BASIC OPERATION

Base Unit Paging Handset

When the INT.COM key is pressed on the Base Unit, the Handset will ring dif- ferently than its incoming call ring. The LCD will display BASE PAGING HAND- SET, as well. The Handset user can then do the following:

•Press INT.COM. The Base Unit and Handset are now in INTERCOM mode.

•Press OFF. The alerting ring will stop.

•Let the ringing continue. It will stop after 5 rings.

Handset Paging Base Unit

When the INT.COM key is pressed on the Handset, the Base Unit rings once, and then automatically enters INTER- COM mode. The person at the Base Unit does not need to press any keys to respond to the Handset.

While in INTERCOM mode, either party can press OFF to terminate this feature.

If a call comes in while your VT 2960 is in INTERCOM mode, the Handset and Base Unit will ring normally. Once the appropriate LINE key is pressed on ei- ther component, you will be connected with the caller, and the INTERCOM mode is terminated.

Image 23

Contents Introduction 900MHz Operation Special FeaturesLine OFF Parts Check ListImportant Safety Instructions Important Safety Instructions Charging the Handset batteries Rechargeable Battery PacksTo Charge The Battery Pack Spare Battery Charger267-7377in Canada Replacing The Handset Battery PackUse only Vtech battery Position the wall mounting bracket on the Base Wall MountingHandset Features Tone KEY Line 1 KEYLine 2 KEY OFF KEYLine 2 is on a call and Line 1 is on Redial KEYHOLD/PAUSE KEY CONFERENCE/CLEAR CONF/ Clear KEYVolume Control KEY Examples of the LCD Display Examples of the LCD Display Examples of the LCD Display Base Unit Features Base Unit FeaturesIntercom LED Base LED Indicators Power LEDSpare Battery LED Charge LEDHold KEY Volume UP & Down KeysTONE/PULSE Switch Conf KEYConnect the telephone line cords Setting up your VTech VTGetting Started PreferencePress the HOLD/PAUSE key to place a call on Hold Basic OperationsMaking Calls To put a call on Hold from the HandsetHandset Base Unit Speakerphone Answering Calls fromCall Waiting Switching from Handset to Base or Base to HandsetSwitching from Handset to Base Unit Speakerphone Switching from Speakerphone to HandsetHandset Paging Base Unit Basic OperationBase Unit Paging Handset Programming the Ringer Advanced OperationsConference Calls Redial Programming the Base Unit RingerMemory Dialing CationDelete ALL? DEL to Allow Speed Dial LocationChanging Stored Numbers To delete all phone numbers stored in MemoryExamples of Caller ID Displays CID-CALLER IDCharacters, including spaces Call is displayedDeleting ALL CID records Deleting CID RecordsDeleting a single CID record Deleting Single CallProgram Location VT2960 Answering System Setting ANNOUNCE-ONLY Mode Call Screening Setting the Number of RingsNumber of Rings selected is Audible Message Alert R e s s S T O P / P L AY t o e x i t programming modeSetting the DAY and Time Skip VolumeSelecting Lines for Message Playback PlayAdvanced Functions Memo RecordingBasic Functions Headset Into Headset Installation and Operating InstructionsInstallation Plug the OptionalMaintenance Taking Care of Your Telephone MaintenanceNo Dial Tone Handset does not Ring When YOU Receive a CallCase of Difficulty Phone DOESN’T Work AT ALLFound Channel YOU Hear Other Calls While Using Your PhoneMake sure the power cord is plugged Common Cure for Electronic EquipmentWarranty Statement What does OUR Warranty not COVER? FCC Part FCC and IC RegulationsUnited States Vtech Communications Canada Vtech ElectronicsFCC and IC Regulations This telephone is registered for use in Canada IC Industry CanadaSpecifications Table of Contents Headset Installation and Operating Instructions Maintenance Issue