VTech VT 2960 instruction manual Programming the Base Unit Ringer, Memory Dialing, Cation, Redial

Page 25

ADVANCED OPERATIONS

Programming the Base Unit Ringer

1.Press and hold the MEM/PROG key until the LCD displays

PROGRAM LOCATION _ _.

2.Press #. LCD displays

?: 1=HANDSET 2=BASE.

3.Press 2. LCD displays

?: 1=LINE 1 2=LINE 2.

4.Press 1 (or 2, depending on which line you’re programming).

5.Press 1,2,3, or 4. The Base Unit will generate the tone you’ve se- lected. Press any of the other ringer selections (1,2,3,4) to compare the different tones.

6.Once you have selected a ringer tone, press OFF.

To turn the Base Unit ringer OFF, locate the L1 RINGER and L2 RINGER ON/OFF switches, on the right-hand edge (antenna side) of the Base Unit.

NOTE: Adjusting the Base Unit ringer switches does not affect the Handset ringer settings.

MEMORY DIALING

Your VT 2960 can store 20 phone num- bers in memory. Each phone number can contain up to 20 digits.

Programming Phone Numbers into Memory

1.With the Handset OFF, enter the tel- ephone number you wish to store. View the number on the LCD to make sure you’ve entered it correctly. If you’ve made a mistake, either press and hold the CONF/CLEAR key to erase the entire string of numbers, or press and hold the INT.COM/DEL key, which will backspace your entry, one digit at a time.

2.Press and hold MEM/PROG.

The LCD displays PROGRAM LO-

CATION _ _.

3.Enter a 2-digit memory location (01 - 20). The Handset will emit a war- bled, happy tone to confirm success- ful programming.

If the LCD displays PROGRAMMING INCOMPLETE,repeat STEPS 1-3.

Storing a Phone Number from

REDIAL

1.With the Handset OFF, press REDIAL. The last phone number you called will be displayed on the LCD.

2.Press and hold MEM/PROG. The LCD displays PROGRAM LOCA-

TION _ _.

3.Enter a 2-digit memory location (01- 20). The Handset will emit a war- bled, happy tone to confirm success- ful programming.

Storing a Pause in a Phone Number

To insert a pause when programming a phone number into memory, press the HOLD/PAUSE key at the appropriate point in the number sequence. A P will be displayed on the LCD, and is treated as a stored digit. The pause is approxi- mately 2 seconds. For a longer pause, press HOLD/PAUSE two or more times.

For example, to store 9-PAUSE-555-1234 in Memory Location 08:

1.Press 9

2.Press HOLD/PAUSE

3.Enter 5551234

4.Press and hold MEM/PROG

5.Enter 08

25

Image 25
Contents Introduction 900MHz Operation Special FeaturesLine OFF Parts Check ListImportant Safety Instructions Important Safety Instructions To Charge The Battery Pack Rechargeable Battery PacksSpare Battery Charger Charging the Handset batteriesUse only Vtech battery Replacing The Handset Battery Pack267-7377in Canada Position the wall mounting bracket on the Base Wall MountingHandset Features Line 2 KEY Line 1 KEYOFF KEY Tone KEYHOLD/PAUSE KEY Redial KEYCONFERENCE/CLEAR CONF/ Clear KEY Line 2 is on a call and Line 1 is onVolume Control KEY Examples of the LCD Display Examples of the LCD Display Examples of the LCD Display Base Unit Features Base Unit FeaturesSpare Battery LED Base LED Indicators Power LEDCharge LED Intercom LEDTONE/PULSE Switch Volume UP & Down KeysConf KEY Hold KEYGetting Started Setting up your VTech VTPreference Connect the telephone line cordsMaking Calls Basic OperationsTo put a call on Hold from the Handset Press the HOLD/PAUSE key to place a call on HoldHandset Base Unit Speakerphone Answering Calls fromSwitching from Handset to Base Unit Speakerphone Switching from Handset to Base or Base to HandsetSwitching from Speakerphone to Handset Call WaitingBase Unit Paging Handset Basic OperationHandset Paging Base Unit Conference Calls Advanced OperationsProgramming the Ringer Memory Dialing Programming the Base Unit RingerCation RedialChanging Stored Numbers Speed Dial LocationTo delete all phone numbers stored in Memory Delete ALL? DEL to AllowCharacters, including spaces CID-CALLER IDCall is displayed Examples of Caller ID DisplaysDeleting a single CID record Deleting CID RecordsDeleting Single Call Deleting ALL CID recordsProgram Location VT2960 Answering System Setting ANNOUNCE-ONLY Mode Number of Rings selected is Setting the Number of RingsCall Screening Setting the DAY and Time R e s s S T O P / P L AY t o e x i t programming modeAudible Message Alert Selecting Lines for Message Playback VolumePlay SkipBasic Functions Memo RecordingAdvanced Functions Installation Headset Installation and Operating InstructionsPlug the Optional Headset IntoMaintenance Taking Care of Your Telephone MaintenanceCase of Difficulty Handset does not Ring When YOU Receive a CallPhone DOESN’T Work AT ALL No Dial ToneMake sure the power cord is plugged YOU Hear Other Calls While Using Your PhoneCommon Cure for Electronic Equipment Found ChannelWarranty Statement What does OUR Warranty not COVER? United States FCC and IC RegulationsVtech Communications Canada Vtech Electronics FCC PartFCC and IC Regulations This telephone is registered for use in Canada IC Industry CanadaSpecifications Table of Contents Headset Installation and Operating Instructions Maintenance Issue