VTech VT 2960 instruction manual Specifications

Page 45

SPECIFICATIONS

FREQUENCY CONTROL

Crystal Controlled Dual PLL Synthesizer

TRANSMIT FREQUENCY

Handset: 925.05 MHz to 927.75 MHz (All ten channels within this range)

Base : 902.3 MHz to 905.0 MHz (All ten channels within this range)

RECEIVE FREQUENCY

Handset: 902.3 MHz to 905.0 MHz (All ten channels within this range)

Base : 925.05 MHz to 927.75 MHz (All ten channels within this range)

NOMINAL EFFECTIVE RANGE Maximum power allowed by FCC and IC. Actual operating range may vary ac- cording to environmental conditions at the time of use.

SIZE

Handset: 202x64x46 mm (LxWxT) Maximum (Antenna excluded)

Base : 225x205x64.5mm (LxWxT) Maximum (Antenna excluded)

WEIGHT

Handset : 292 g (Battery included)

Base : 800 g

POWER REQUIREMENTS

Handset : Self-contained nickel-cadmium rechargeable battery supply, 3.6V nomi- nal, 600mAh capacity.

Base : 11V DC 600mA

MEMORY

Speed Dial: 20 Memory locations,20 digits per location.

CID	: Alpha Numeric Display 50
	Memory locations.
ITAD	: 15 minutes of Digital record
	time from all sources.

VTECH reserves the right to make design and specification changes for product improvement without prior notice.

45

Image 45

Contents Introduction 900MHz Operation Special FeaturesLine OFF Parts Check ListImportant Safety Instructions Important Safety Instructions To Charge The Battery Pack Rechargeable Battery PacksSpare Battery Charger Charging the Handset batteriesReplacing The Handset Battery Pack Use only Vtech battery267-7377in Canada Position the wall mounting bracket on the Base Wall MountingHandset Features Line 2 KEY Line 1 KEYOFF KEY Tone KEYHOLD/PAUSE KEY Redial KEYCONFERENCE/CLEAR CONF/ Clear KEY Line 2 is on a call and Line 1 is onVolume Control KEY Examples of the LCD Display Examples of the LCD Display Examples of the LCD Display Base Unit Features Base Unit FeaturesSpare Battery LED Base LED Indicators Power LEDCharge LED Intercom LEDTONE/PULSE Switch Volume UP & Down KeysConf KEY Hold KEYGetting Started Setting up your VTech VTPreference Connect the telephone line cordsMaking Calls Basic OperationsTo put a call on Hold from the Handset Press the HOLD/PAUSE key to place a call on HoldHandset Base Unit Speakerphone Answering Calls fromSwitching from Handset to Base Unit Speakerphone Switching from Handset to Base or Base to HandsetSwitching from Speakerphone to Handset Call WaitingBasic Operation Base Unit Paging HandsetHandset Paging Base Unit Advanced Operations Conference CallsProgramming the Ringer Memory Dialing Programming the Base Unit RingerCation RedialChanging Stored Numbers Speed Dial LocationTo delete all phone numbers stored in Memory Delete ALL? DEL to AllowCharacters, including spaces CID-CALLER IDCall is displayed Examples of Caller ID DisplaysDeleting a single CID record Deleting CID RecordsDeleting Single Call Deleting ALL CID recordsProgram Location VT2960 Answering System Setting ANNOUNCE-ONLY Mode Setting the Number of Rings Number of Rings selected isCall Screening R e s s S T O P / P L AY t o e x i t programming mode Setting the DAY and TimeAudible Message Alert Selecting Lines for Message Playback VolumePlay SkipMemo Recording Basic FunctionsAdvanced Functions Installation Headset Installation and Operating InstructionsPlug the Optional Headset IntoMaintenance Taking Care of Your Telephone MaintenanceCase of Difficulty Handset does not Ring When YOU Receive a CallPhone DOESN’T Work AT ALL No Dial ToneMake sure the power cord is plugged YOU Hear Other Calls While Using Your PhoneCommon Cure for Electronic Equipment Found ChannelWarranty Statement What does OUR Warranty not COVER? United States FCC and IC RegulationsVtech Communications Canada Vtech Electronics FCC PartFCC and IC Regulations This telephone is registered for use in Canada IC Industry CanadaSpecifications Table of Contents Headset Installation and Operating Instructions Maintenance Issue