Patton electronic 4940 manual Copy tftp//tftpserveraddress/server path/b1 flash

Page 32

SmartNode 4940 Getting Started Guide4 • Initial configuration

Step

Command

Purpose

 

 

 

8

RedBoot> go

Starts the application image that was down-

 

 

loaded into the volatile memory (RAM).

 

 

 

Note With the Bootloader, only the Ethernet interface 0/0 is available. The Boot- loader applies the IP address, subnet mask, and default gateway that were last configured by the Bootloader itself or by another application (e.g. Smart- Ware). If an application configured the Ethernet interface 0/0 to use DHCP, the Bootloader will also use DHCP to learn the interface configuration. It can receive and apply the IP address, subnet mask, default gateway, and default (TFTP) server (transmitted as basic DHCP information ‘Next server IP address’).

Note This procedure does not download the respective CLI description file.

Download it after starting up SmartWare with the following command:

copy tftp://<tftp_server_address>/<server path>/b1 flash:

Example: Downloading and storing a new application image (SmartWare)

RedBoot> ip

-l

172.16.40.98/19

RedBoot> ip

-g

172.16.32.1

RedBoot> ping -h

172.16.32.100

Network PING -

from 172.16.40.98 to 172.16.32.100

..........PING

-

received 10 of 10 expected

RedBoot> load -r -v -h 172.16.32.100 -b 0x1800100 /Sn4xxx/image.bin Using default protocol (TFTP)

-

Raw file loaded 0x01800100-0x0199ca6b, 1689964 bytes, assumed entry at 0x01800100

RedBoot> fis delete -n 1

Delete image 1 - continue (y/n)? y

... Erase from 0x60030000-0x601cc974: ..........................

RedBoot> fis create

Use address 0x01800100, size 1684402 ? - continue (y/n)? y

... Erase from 0x60030000-0x601cb3ba:

..........................

... Program from 0x00011eec-0x00011ef4 at 0x60030000: .

... Program from 0x01800100-0x0199b4b2 at 0x60030008:

... Program from 0x00011eec-0x00011ef4 at 0x60030000: .

Image successfully written to flash

 

RedBoot> fis list -l

 

 

Id Address

Length

State

Description

Entry

Load Addr

 

Version

--------------------------------------------------------------------

1 0x60030000

1693438

valid

SmartWare R5.T BUILD28015

0x01800100

0x01800100

 

V5.T

RedBoot>

go

 

 

 

Starting

'SmartWare R5.T

BUILD28015' at 0x01800100 via 0x01800100

Bootloader

32

Image 32
Contents SmartNode 4940 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables Structure About this guideAudience Precautions Impaired functioningSafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations Chapter contents General informationSmartNode 4940 overview SmartNodeSN4940 model codes SN4941 model codesSmartNode 4940 rear panel SmartNode 4940 rear panel ports are described in tableDC power input SmartNode 4940 front panel SN4940/4E120VLED Applications overview Introduction Application-Convert Legacy PBX to VoIPSmartNode installation Planning the installation Network DiagramSite log Network informationInstalling the gateway Connecting the PRI Connecting the power supply Initial configuration Factory-default IP settings Configuring the desired IP addressConnecting the SmartNode to the network Loading the configuration optional Connecting the SmartNode to the networkBootloader Start BootloaderStart-up with factory configuration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbersAppendix a Compliance information Safety ComplianceRadio and TV Interference Pstn RegulatoryFCC Part 68 Acta Statement Industry Canada NoticeCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Voice processing signalling dependent Voice connectivityData connectivity Fax and modem supportVoice routing-session router Voice signallingIP services Physical ManagementSystem Identification of the SmartNode devices via Snmp SmartNode Model SysObjectIDSmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Pin Signal Console portPRI port Appendix E SmartNode 4940 factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses