Patton electronic 4940 manual End User License Agreement

Page 58

SmartNode 4940 Getting Started Guide

F • End user license agreement

 

 

End User License Agreement

By opening this package, operating the Designated Equipment or downloading the Program(s) electronically, the End User agrees to the following conditions:

1. Definitions

A)Effective Date shall mean the earliest date of purchase or download of a product containing the Patton Electronics Company Program(s) or the Program(s) themselves.

B)Program(s) shall mean all software, software documentation, source code, object code, or executable code.

C)End User shall mean the person or organization which has valid title to the Designated Equipment.

D)Designated Equipment shall mean the hardware on which the Program(s) have been designed and pro- vided to operate by Patton Electronics Company.

2. Title

Title to the Program(s), all copies of the Program(s), all patent rights, copyrights, trade secrets and proprietary information in the Program(s), worldwide, remains with Patton Electronics Company or its licensors.

3. Term

The term of this Agreement is from the Effective Date until title of the Designated Equipment is transferred by End User or unless the license is terminated earlier as defined in section “6. Termination” on page 59.

4. Grant of License

A)During the term of this Agreement, Patton Electronics Company grants a personal, non-transferable, non-assignable and non-exclusive license to the End User to use the Program(s) only with the Designated Equipment at a site owned or leased by the End User.

B)The End User may copy licensed Program(s) as necessary for backup purposes only for use with the Des- ignated Equipment that was first purchased or used or its temporary or permanent replacement.

C)The End User is prohibited from disassembling; decompiling, reverse-engineering or otherwise attempt- ing to discover or disclose the Program(s), source code, methods or concepts embodied in the Program(s) or having the same done by another party.

D)Should End User transfer title of the Designated Equipment to a third party after entering into this license agreement, End User is obligated to inform the third party in writing that a separate End User License Agreement from Patton Electronics Company is required to operate the Designated Equipment.

5. Warranty

The Program(s) are provided as is without warranty of any kind. Patton Electronics Company and its licensors disclaim all warranties, either express or implied, including but not limited to the implied warranties of mer- chantability, fitness for a particular purpose or non-infringement. In no event shall Patton Electronics Com- pany or its licensors be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or inability to use the Program(s), even if Patton Electronics Company has been advised of the possibil- ity of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you.

End User License Agreement

58

Page 57 Page 59
Image 58
Page 57 Page 59
Contents SmartNode 4940 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables Audience About this guideStructure Precautions Impaired functioningSafety when working with electricity General observations Typographical conventions used in this documentGeneral conventions Chapter contents General informationSmartNode 4940 overview SmartNodeSN4940 model codes SN4941 model codesSmartNode 4940 rear panel SmartNode 4940 rear panel ports are described in tableDC power input SmartNode 4940 front panel SN4940/4E120VLED Applications overview Introduction Application-Convert Legacy PBX to VoIPSmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway Connecting the PRI Connecting the power supply Initial configuration Connecting the SmartNode to the network Configuring the desired IP addressFactory-default IP settings Loading the configuration optional Connecting the SmartNode to the networkBootloader Start BootloaderStart-up with factory configuration Load a new application image SmartWare via TftpCopy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial linkContacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference SafetyCompliance Pstn RegulatoryFCC Part 68 Acta Statement Industry Canada NoticeCE Declaration of Conformity Authorized European RepresentativeAppendix B Specifications Data connectivity Voice processing signalling dependentVoice connectivity Fax and modem supportIP services Voice signallingVoice routing-session router System ManagementPhysical Identification of the SmartNode devices via Snmp SmartNode Model SysObjectIDSmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal ConsoleEthernet E1 PRI T1 PRI Appendix D Port pin-outs Pin Signal Console portPRI port Appendix E SmartNode 4940 factory configuration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses
Top Page Image Contents