Patton electronic 4940 manual Termination, Other licenses

Page 59

SmartNode 4940 Getting Started Guide

F • End user license agreement

 

 

If the Program(s) are acquired by or on behalf of a unit or agency of the United States Government, the Gov- ernment agrees that such Program(s) are commercial computer software or computer software documentation and that, absent a written agreement to the contrary, the Government’s rights with respect to such Program(s) are limited by the terms of this Agreement, pursuant to Federal Acquisition Regulations 12.212(a) and/or DEARS 227.7202-1(a) and/or sub-paragraphs (a) through (d) of the “Commercial Computer Software - Restricted Rights” clause at 48 C.F.R. 52.227-19 of the Federal Acquisition Regulations as applicable.

6. Termination

A)The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s).

B)Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section “4. Grant of License” on page 58.

C)Upon termination for A or B above or the end of the Term, End User is required to destroy all copies of the licensed Program(s)

7. Other licenses

The Program may be subject to licenses extended by third parties. Accordingly, Patton Electronics Company licenses the Programs subject to the terms and conditions dictated by third parties. Third party software identi- fied to the Programs includes:

•A routing license is included at no charge.

•MGCP capabilities will require the purchase of an additional license.

•The LGPL (Lesser General Public License) open source license distributed to you pursuant to the LGPL license terms (http://www.gnu.org/licenses/lgpl.html).

•RedBoot (Red Hat Embedded Debug and Bootstrap) embedded system debug/bootstrap environment from Red Hat distributed to you pursuant to the eCos license terms (http://ecos.sourceware.org/license- overview.html) and GNU General Public License (GPL) terms (http://www.gnu.org/copyleft/gpl.html). Source code is available upon request.

End User License Agreement

59

Page 58 Page 59
Image 59
Page 58 Page 59
Contents SmartNode 4940 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General conventions Typographical conventions used in this documentGeneral observations General information Chapter contentsSmartNode SmartNode 4940 overviewSN4941 model codes SN4940 model codesSmartNode 4940 rear panel ports are described in table SmartNode 4940 rear panelDC power input SN4940/4E120V SmartNode 4940 front panelLED Applications overview Application-Convert Legacy PBX to VoIP IntroductionSmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway Connecting the PRI Connecting the power supply Initial configuration Factory-default IP settings Configuring the desired IP addressConnecting the SmartNode to the network Connecting the SmartNode to the network Loading the configuration optionalStart Bootloader BootloaderLoad a new application image SmartWare via Tftp Start-up with factory configurationCopy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional informationContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceAppendix a Compliance information Pstn Regulatory SafetyCompliance Radio and TV InterferenceIndustry Canada Notice FCC Part 68 Acta StatementAuthorized European Representative CE Declaration of ConformityAppendix B Specifications Fax and modem support Voice processing signalling dependentVoice connectivity Data connectivityVoice routing-session router Voice signallingIP services Physical ManagementSystem SmartNode Model SysObjectID Identification of the SmartNode devices via SnmpSmartNode Model SysObjectID Appendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs Console port Pin SignalPRI port Appendix E SmartNode 4940 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination
Top Page Image Contents