GE 2-9892 manual Room, Monitor, If Tape is full, unit will beep after tenth ring, Remote on

Page 24

REMOTE OPERATION

	Leave your radio on? Your TV? Is someone in the area of your		•	D. Remote
	Answer-PhoneTM? While away you can call your Answer-PhoneTM		•	Room
	to monitor the room in which the phone is located.		•	Room
	to monitor the room in which the phone is located.		•	Monitor
			•
	1.	After hearing three short beeps Press 3.	•
	2.	Unit will turn on microphone for one minute then three beeps. •
	3.	To continue listening Press 3.	•
	4.	To end Room Monitor Press 6.	•
			•
	If Tape is full, unit will beep after tenth ring		•	H. Remote
	1.	Dial three digit security code.	•	Message
	1.	Dial three digit security code.	•	Message
	2.	Unit will rewind and playback messages.	•	Playback if
	3.	Unit will beep three times when finished.	•	Tape is Full
	3.	Unit will beep three times when finished.	•
	4.	You can dial a remote command or hang up.	•
	4.	You can dial a remote command or hang up.	•
			•

	If the unit is in ANSWER OFF mode, unit will beep after tenth		•	I. Remote ON
			•	I. Remote ON
	ring.		•
	ring.		•
	To Turn Answer-PhoneTMon		•
	To Turn Answer-PhoneTMon		•
	1.	After beep, dial three digit security code.	•
	1.	After beep, dial three digit security code.	•
	2.	You can dial a remote command or hang up.	•
	2.	You can dial a remote command or hang up.	•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

24

Image 24

Contents Answer-PhoneTMwith Voice Time/Day Stamp Table of Contents Introduction Parts Check ListFull Feature Telephone Number Memory Hearing Aid Compatible Telephone FeaturesCall Screening Speaker Power Failure ProtectionTM Music during tape shuttleOne-Touch operation for ease of use Line Memory Store/In Button Stores phone numbers in phone memory Handset Coiled CordTelephone Controls Door Opens for access to controls of the answering system Message Reset Button Resets and clears all messagesSpeaker Answerer ControlsSecurity Code, on bottom of unit, not shown Installation Desk or Table TOP Connect the Coiled CordConnect the Long Telephone Line Cord Plug in the Power Supply Install the Base Plate so that the Arrows Face Upward Installation for Wall Mount UseReverse the Handset Hook Remove the Base PlateInstallation Wall Mount AnswerphonePULSE/TONE Switch Ringer VolumeTelephone Operation To Make a CallHow to Use AutomaticWait for dial tone Press Redial Button Refer to the telephone company’s instruction on useTelephone Memory Operation Frequently Called Numbers in Memory For Example Memory LocationTo initiate Chain Dialing Adjust Volume control to a comfortable level Introduction Setting Time/Day StampAnswering System Operation To set hourAnswer LED as a ready indicator Answer LED as an IN-USE IndicatorTo set day Checking the Time/Day StampTo Play Incoming Messages To Stop PlaybackTo Repeat Playback You find a comfortable volume level Message ResetTape Press and hold down Memo button. Start recording afterRemote Operation To Play Messages from a remote locationTo Replay Messages To Reset Incoming Message Tape To ResetTo Leave a Remote Memo To Record a New Outgoing AnnouncementRoom MonitorIf Tape is full, unit will beep after tenth ring Remote onCase of Difficulty Answerer Problem Solution Battery CARTRIDGE, pop it up, lift Battery out Following manner Accessory Order Form 9892 ONE Year Limited Warranty What will we do?FCC Registration Information Interference InformationHearing AID Compatibility S W E R P H O N E TM