GE 2-9892 manual Answerer Problem Solution

Page 26

IN CASE OF DIFFICULTY

 

ANSWERER PROBLEM

SOLUTION

 

 

1.

Tape won’t go in.

Unplug the DC power cord and plug it in again.

 

 

 

 

 

 

 

Wait for unit to stop. Then, insert tape. Unplug

 

 

 

2. Power was applied without tape

 

 

 

 

 

DC power cord.

 

 

 

 

 

installed

 

Then plug it in again. (This resets the unit).

 

 

 

 

 

 

 

 

 

 

3.

Answer indicator flashes rapidly

Record new Outgoing Announcement.

 

 

 

and there are no new messages

If problem recurs, clean heads.

 

 

 

4. Answer ON/OFF is not on

Is Answerer switched ON? Press Answer

 

 

 

 

 

 

 

ON/OFF switch.

 

 

 

 

 

 

Is the DC Adapter inserted properly and securely

 

 

 

 

 

 

 

into working AC outlet?

 

 

5.

Unit will not function when I press

If tape is running, wait for tape to finish rewind.

 

 

 

 

 

any buttons.

 

Note: Do not plug unit in without tape installed.

 

 

 

 

 

 

Unplug AC power cord. Then plug it in again.

 

 

 

 

 

 

 

(This resets the unit.)

 

 

6.

The unit does not function.

Replace tape and unplug and then plug in DC

 

 

 

 

 

However, Beep sounds and Call

 

power cord. (This resets the unit).

 

 

 

 

 

Counter flashes.

If tape is running, wait for tape to finish rewind.

 

 

 

 

 

 

 

Note: Do not plug unit in without tape installed.

 

 

7.

The unit does not record Incoming

Is tape inserted properly?

 

 

 

 

 

messages

Does tape appear damaged? If so, replace.

 

 

 

 

 

 

Is Outgoing Message recorded properly?

 

 

 

 

 

 

 

 

 

8. Sound level of Messages played

Turn Volume Control up.

 

 

 

 

 

back is low

Clean the head and capstan assembly

 

 

 

 

 

 

 

 

 

9. Outgoing Announcement does not

Re-Record Outgoing Announcement.

 

 

 

 

 

stop and no incoming message is

Clean the head and capstan assembly

 

 

 

 

 

recorded

 

 

 

 

 

 

REMOTE OPERATION

 

 

 

 

 

 

PROBLEM

SOLUTION

 

 

 

 

1. System does not respond to

Check to make sure you are using Touch-Tone

 

 

 

 

 

commands

 

phone.

 

 

 

 

 

 

Start entering codes before ten second time-out.

 

 

 

 

 

 

Enter correct three digit security code.

 

 

 

 

 

 

Press dial buttons firmly. (There may be noise

 

 

 

 

 

 

 

interference on the phone lines.)

 

 

2.

System doesn’t answer until the

Answerer is turned off.

 

 

 

 

 

tenth ring.

Enter three digit security code to turn on (p. 24).

 

 

 

 

 

 

If tape is full, enter Security Code, then listen to

 

 

 

 

 

 

 

and delete messages to make room for more

 

 

 

 

 

 

 

messages (p. 24).

 

 

 

 

 

 

 

 

 

 

26

Image 26
Contents Answer-PhoneTMwith Voice Time/Day Stamp Table of Contents Introduction Parts Check ListFull Feature Telephone Number Memory Hearing Aid Compatible Telephone FeaturesOne-Touch operation for ease of use Call Screening Speaker Power Failure ProtectionTMMusic during tape shuttle Line Telephone Controls Memory Store/In Button Stores phone numbers in phone memoryHandset Coiled Cord Speaker Door Opens for access to controls of the answering systemMessage Reset Button Resets and clears all messages Answerer ControlsSecurity Code, on bottom of unit, not shown Connect the Long Telephone Line Cord Installation Desk or Table TOPConnect the Coiled Cord Plug in the Power Supply Reverse the Handset Hook Install the Base Plate so that the Arrows Face UpwardInstallation for Wall Mount Use Remove the Base PlateInstallation Wall Mount AnswerphoneTelephone Operation PULSE/TONE SwitchRinger Volume To Make a CallWait for dial tone Press Redial How to UseAutomatic Button Refer to the telephone company’s instruction on useTelephone Memory Operation To initiate Chain Dialing Frequently Called Numbers in MemoryFor Example Memory Location Answering System Operation Adjust Volume control to a comfortable levelIntroduction Setting Time/Day Stamp To set hourTo set day Answer LED as a ready indicatorAnswer LED as an IN-USE Indicator Checking the Time/Day StampTo Repeat Playback To Play Incoming MessagesTo Stop Playback Tape You find a comfortable volume levelMessage Reset Press and hold down Memo button. Start recording afterTo Replay Messages Remote OperationTo Play Messages from a remote location To Leave a Remote Memo To Reset Incoming Message TapeTo Reset To Record a New Outgoing AnnouncementIf Tape is full, unit will beep after tenth ring RoomMonitor Remote onCase of Difficulty Answerer Problem Solution Battery CARTRIDGE, pop it up, lift Battery out Following manner Accessory Order Form 9892 ONE Year Limited Warranty What will we do?Hearing AID Compatibility FCC Registration InformationInterference Information S W E R P H O N E TM