GE 2-9892 manual Battery CARTRIDGE, pop it up, lift Battery out

Page 27

PRODUCT CARE and SERVICE

A consumer replaceable long-life Lithium Batter (3V) is installed

A. To Replace

in the phone to provide back-up power for retaining numbers in

Backup

memory. The LITHIUM BATTERY COMPARTMENT is located on

Battery

the bottom of the TELEPHONE BASE.

 

 

 

 

1. Unplug the power supply and unplug PHONE LINE from

 

 

 

telephone outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Unsnap the battery door

 

 

• Using a screwdriver, insert in opening at either end of

 

 

BATTERY CARTRIDGE, pop it up, lift BATTERY out.

 

 

Dispose of BATTERY CARTRIDGE. When discarding

 

 

batteries, be sure to dispose of them in the proper manner,

 

 

according to your state and local regulations.

 

 

 

 

3. Replace battery cartridge and door

 

 

 

Note: CARTRIDGE can be inserted only one way.

 

 

 

 

 

 

 

4. Plug in the power supply and plug in the PHONE CORD

 

 

 

Note: Numbers in memory must be reprogrammed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For your safety, please follow these simple precautions:

B. Battery

Do not recharge, disassemble, mutilate, puncture, wet or

Safety

 

dispose of Battery in fire. Like other batteries of this type, if it is

 

Precautions

 

burned or punctured, it could release toxic material which

 

 

could cause injury.

 

 

 

Keep Battery out of reach of children.

 

 

Replace only with GE Cat. #5-1923. Accessory Order Form

 

 

 

included in this guide.

 

 

 

 

 

 

27

Image 27
Contents Answer-PhoneTMwith Voice Time/Day Stamp Table of Contents Parts Check List IntroductionHearing Aid Compatible Telephone Features Full Feature Telephone Number MemoryCall Screening Speaker Power Failure ProtectionTM Music during tape shuttleOne-Touch operation for ease of use Line Memory Store/In Button Stores phone numbers in phone memory Handset Coiled CordTelephone Controls Answerer Controls Door Opens for access to controls of the answering systemMessage Reset Button Resets and clears all messages SpeakerSecurity Code, on bottom of unit, not shown Installation Desk or Table TOP Connect the Coiled CordConnect the Long Telephone Line Cord Plug in the Power Supply Remove the Base Plate Install the Base Plate so that the Arrows Face UpwardInstallation for Wall Mount Use Reverse the Handset HookAnswerphone Installation Wall MountTo Make a Call PULSE/TONE SwitchRinger Volume Telephone OperationButton Refer to the telephone company’s instruction on use How to UseAutomatic Wait for dial tone Press RedialTelephone Memory Operation Frequently Called Numbers in Memory For Example Memory LocationTo initiate Chain Dialing To set hour Adjust Volume control to a comfortable levelIntroduction Setting Time/Day Stamp Answering System OperationChecking the Time/Day Stamp Answer LED as a ready indicatorAnswer LED as an IN-USE Indicator To set dayTo Play Incoming Messages To Stop PlaybackTo Repeat Playback Press and hold down Memo button. Start recording after You find a comfortable volume levelMessage Reset TapeRemote Operation To Play Messages from a remote locationTo Replay Messages To Record a New Outgoing Announcement To Reset Incoming Message TapeTo Reset To Leave a Remote MemoRemote on RoomMonitor If Tape is full, unit will beep after tenth ringCase of Difficulty Answerer Problem Solution Battery CARTRIDGE, pop it up, lift Battery out Following manner Accessory Order Form 9892 What will we do? ONE Year Limited WarrantyFCC Registration Information Interference InformationHearing AID Compatibility S W E R P H O N E TM