Aiphone IS Series operation manual Other buttons, Sub stations, How to select multiple stations

Page 13

Registering stations and PA outputs [System setting – Registering stations]

Register all the stations and PA outputs connected in the system, and set the area, station no., station name (or PA output name) and type of station (for sub stations: video door/ audio door/room sub stations) to them.

1 Click Registering stations in the table of contents.

2 Set the area, station no., station name and type of station (for sub stations) to the target stations, and enter names to the target PA outputs.

*Setting the station no. is required.

*Shows a port no. of the control unit to connect with a station.

*It is required to enter a name to the target PA output when an external unit is connected to the corresponding PA output terminals.

*For a cell with the mark, select the target one from the pull-down menu.

*Do not set stations with the same number in an area.

NOTE:

The name of a master station displayed on its monitor in standby mode is up to 16 alphanumeric characters.

Other buttons

•Connection check

Click to confirm the connected units.

Connected: yellowish green

Not connected: gray

Station type error: pink

•[Collective setting]:

The following buttons are used to make the settings to all the checked stations at one time.

*Pressing each button opens another window.

NOTE:

Be sure to check all the target stations before using these buttons.

•Area

Click to set the same area number to all the checked stations.

•Station number

 

Click to assign sequential numbers to all the checked

 

 

stations from top to bottom. The number you enter will

 

 

 

 

be set as the first number and will be assigned to the top

GETTING

 

station of the ones checked. Other checked stations will

 

 

 

be numbered sequentially.

STARTED

•

 

 

 

 

Station name

 

 

 

Click to assign the same station (and/or PA output) name

 

 

and sequential numbers to all the checked stations (and/

 

 

or PA outputs) from the top down. Enter a name only.

 

 

 

•

 

 

(sub stations)

 

Station type

SETTING

 

stations.

 

Click to set the same station type to all the checked sub

 

How to select multiple stations

THE

 

register.

SYSTEM

○ Click to check the stations and PA outputs you will

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

USING THE SYSTEM

○ By clicking the button for the control unit, all the stations

 

and PA outputs connected to it are checked or canceled.

 

 

APPENDIX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

○By clicking the button on the top of the list, you can check or cancel all the stations and PA outputs on the list.

3 Click Temporarily stored to save the current setting results temporarily.

*If you wish to cancel the setting results you have made, click a title in the table of contents or “Refresh” in the web browser menu.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Setting Manual Contents About this Manual Purpose of the System SettingsManual configurations Dhcp Setting ListON/OFF Title Sub titleDS1 SS1NTP DT1/DT2JAN Starting UP the System When connecting a PC to the central control unitSystem requirements for PC Connect a PC to the central control unitLog in to the system by setting the following items Setting the system configuration System configurationPassword Enter aiphone Start up the PC, and then open the browser windowBasic setting procedure Making the System SettingsSelecting the network setting method Making network settings Network settingDhcp Static IP AddressRegistering zones System setting Zone registration Registering areas System setting Area registration RequiredClick Control units composition in the table of contents Setting the station no. is required How to select multiple stationsCollective setting Other buttonsClick Advanced station settings in the table of contents Basic setting procedureWhen you have finished making all the detailed settings Settings on Called stations setting windowSettings on Contact input window for room sub stations only Making detailed settings to master stationsSettings on Other window Settings on Stations to be scan monitored windowSelect an output terminal from the pull-down menu Settings on Contact output windowSound file specifications Click Registering sound source in the table of contentsClick Registering sound sequences in the table of contents Chime setting Registering daily chime scheduleRegistering daily chime schedule Click Registering daily chime schedule in the tableSettings on Weekly schedule setting window Click Chime schedule setting in the table of contentsSettings on Individual schedule setting window Downloading chime schedule dataClick Registering daily transfer schedule Click Transfer schedule setting in the table of contentsSetting the timer Timer setting Downloading/uploading setting data Setting file Setting time and date Time and date settingWhen downloading setting data onto the PC When uploading setting dataMaintenance
Top Page Image Contents