Hitachi HPW-200EC manual S11 Dtmf Tone Duration, S12 Escape Guard Time, S36 Lapm Failure Control

Page 51

S11 - DTMF Tone Duration

Sets the duration of tones in DTMF dialing. This value has no effect on pulse dialing.

Range: 50-255 milliseconds

Default: 95 (95 milliseconds)

S12 - Escape Guard Time

Defines the guard time for the escape sequence, in fiftieths of a second.

Range: 0-255 1/50ths of a second

Default: 50 (1 second)

S36 - LAPM Failure Control

This value indicates what should happen upon a LAPM failure. If an invalid number is entered, the number is accepted into the register, but S36 will act as if the default value has been entered.

0=Modem disconnects

1=Modem stays on-line and a Normal mode connection is established

2=Modem stays on-line and a Normal mode connection is established

3=Modem stays on-line and a Normal mode connection is established

4=Modem disconnects

5, 6 =Reserved

7 =Modem stays on-line and a Normal mode connection is established (default)

S37 - Desired Line Connection Speed

This register specifies the desired line connection speed.

Default: 0

Desired line connection speed. This is interlinked with the Fn command . If an invalid number is entered, the number is accepted into the register, but S37 will act as if the default value has been entered.

0 = Attempt automode connection (default)

1-3 = Attempt to connect at 300bps. F1 command 4 = Reserved

5 = Attempt to connect at 1200bps. F4 command

6 = Attempt to connect at 2400bps. F5 command

7 = Attempt to connect at V.23. F3 command

8 = Attempt to connect at 4800bps. F6 command

9 = Attempt to connect at 9600bps. F8 command

10 = Attempt to connect at 12000bps. F9 command

11 = Attempt to connect at 14400bps. F10 command

12 = Attempt to connect at 7200bps. F7 command

13 = Attempt to connect at 16800bps

14 = Attempt to connect at 19200bps

15 = Attempt to connect at 21600bps

16 = Attempt to connect at 24000bps

17 = Attempt to connect at 26400bps

18 = Attempt to connect at 28800bps

20 = Attempt to connect at 33600bps

50

Image 51

Contents Handheld PC Hardware Users Guide Information to Users ICES-003 Statement Important Safety InstructionsPage Page Page Industry Canada Terminal Equipment Statement Page Page MIC WelcomePicture from the Bottom of the Handheld PC Running your Handheld PC Batteries and powerOperating your Handheld PC with the Main batteries To insert the rechargeable Li-ion battery packTo change the main battery Operating your Handheld PC with the AC adapter Charging rechargeable Li-ion battery packNotification LED Using the stylus Pen Wireless infrared transferTo use the stylus Pen Left Side View of Handheld PC Interface cablePC card slot To insert a PC cardTo remove a PC card Using the CF card. also known as Compact Flash card To insert a CF cardTo remove a CF card To use a modem RAM/ROM Slot To change ROM board VGA Output Of Pocket PowerPoint Viewer Installation & Start-UpGeneral Description Usage ESC Using the Voice Recorder Page To assign application to User1 and User2 To use Quick Launch KeyTo decrease display contrast Adjusting the display contrastTo use and key To increase display contrastResetting your Handheld PC To perform a simple resetTo perform a full reset Precautions Hardware SpecificationsPhysical Description and Features Weight Peripheral and Transfer Interface PowerCF Card Compatibility PC Card CompatibilityData Compression Error CorrectionCompatibility Specification StandardAnswer Re-execute CommandAT= x Write to Selected S-Register AT? Read Selected S-RegisterEn Command Echo Dn DialDial Modifiers Mn Speaker Control Fn Select Modulation Compatibility onlyHn Disconnect and hook control Modem IdentificationSet Tone Dial Default On Return to On-Line Data ModeSet Pulse Dialing as a default Sn Access S-RegisterXn Extended Result Codes Control RING, no CARRIER, ERROR, no DIALTONE, Connect RateSummary of Supported Result Codes Cn DCD Data Carrier Detect Option Zn ResetFn Restore Default Configuration Yn Long Space DisconnectKn Flow Control Mn Mode SelectionQn Mode Selection Gn Select Guard Tone\Nn Selects Operating Mode Display Current ConfigurationWn Store Current Configuration Yn Selects a Default Reset Profile1.AT% Commands Enable/Disable Data Compression RingConnect 1200 Connect 75 Connect 1200 BusyCompression None Compression V.42bisS1 Ring Counter S0 Number of Rings to Auto-AnswerS4 Line Feed Character S8 Pause Time For Dial DelayS2 Escape Character S3 Carriage Return CharacterS37 Desired Line Connection Speed S11 Dtmf Tone DurationS12 Escape Guard Time S36 Lapm Failure ControlS83 EC Negotiation timeout S38 Delay Before Forced Hang UpFax Modulation Table Value Modulation & Speed +FCLASS=n Select Service Class+Fcommand? Report Active Configuration +Fcommand=? Report Operating Capabilities+FTH=n Transmit Data with Hdlc Framing +FRS=n Receive Silence+FTM=n Transmit Data +FRM=n Receive DataPage Page HDECLARATION of Conformity Spring,1998