Panasonic KX-TG2382B operating instructions Useful Information

Page 73

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact a Factory Servicenter or other Authorized Servicer. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:

1)Remain on the line and briefly explain to the dispatcher the reason for the call.

2)Perform such activities in the off-peak hours, such as early morning or late evenings.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

Privacy of communications may not be ensured when using this phone.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Useful Information

For assistance, please call: 1-800-211-PANA(7262)

73

Page 72 Page 74
Image 73
Page 72 Page 74
Contents Operating Instructions Charge the battery for about 15 hours before initial useAttach your purchase receipt here Energy Star Accessories includedFor extra orders, call For KX-TG2383S users For KX-TG2382B/KX-TG2382PW usersContents Canceling the Handset Registration Temporary Tone Dialing For Rotary or Pulse Service UsersFor Best Performance Battery chargeBase unit location/Noise Base unit Location of ControlsCharger unit Location of Controls How to use the Navigator keyHandset This key has four active areas that are indicated by arrowsConnections InstallationBattery Charge Installing the Battery in the HandsetInstallation ChargingBattery information Battery strengthDisplay prompt Battery strength RechargeTo switch to the speakerphone while using the headset Connecting the optional headset to the handsetBelt Clip Optional HeadsetHow to select a function item from the menu Programmable SettingsProgramming Guidelines Ringer tone GF H=SaveFunction Menu Table Programmable SettingsUseful information Scroll to Date and time by pressing Ö or Ñ Press á Date and TimePress Ö Next key Press á Save keyFor Caller ID service users p Dialing ModeTo check the date/time Select a or B by pressing Ö or Ñ Press á Save key Line ModeSelect On or Off by pressing Ö or Ñ Press á Save key Auto Talk FeatureScroll to Ringer setting by pressing Ö or Ñ, and press á Ringer VolumeSelect the desired volume by pressing Ö or Ñ To turn the ringer onDate and time HInitial set Hlcd contrast Auto talk LCD ContrastLCD contrast LCD contrast Low HighWhen finished, press Press GREETING!REC to start the recording modePreparing the Answering System Greeting MessagePreparing the Answering System Flash Memory Message Backup Message storageTo check the recorded greeting message To erase the recorded greeting messageSelect the recording time by pressing Ö or Caller’s Recording TimeIf you select Greeting only, the unit will answer a Toll saver Number of RingsMaking Calls Using the HandsetPress Dial a phone number Making CallsHands-free Digital Duplex Speakerphone For best performance, please note the followingTo dial after confirming the entered number To redial using the redial list Memory RedialTo redial the last number dialed on the handset To release the hold To put a call on holdLighted handset keypad Backlit LCD displayAuto Talk Answering CallsPressing How caller information is displayed when a call is received Caller ID ServiceViewing the Caller List Using the Caller ListCalling Back from the Caller List Using the Caller ListWhat √ means If a caller calls more than onceEditing the Caller’s Phone Number Caller ID Number Auto Edit Feature pScroll to the desired caller by pressing Or Ñ Press á Scroll to Caller ID edit by pressing Ö or Ñ, and press á Caller ID Number Auto Edit FeatureAuto talk HCaller ID edit Set tel line Auto edit GF H=SaveScroll to Save directory by pressing Ö or Ñ, and press á Storing Caller List Information in the DirectoryCaller list 10 new calls GF H=Directory Edit HSave directoryTo erase a specific caller from the Caller List Erasing Caller List InformationTo erase all entries in the Caller List ClearStoring Names and Numbers DirectoryPress Ö Next key Enter a phone number, up to 22 digits Selecting characters to enter names DirectoryFor example, to enter Tom Jones If you make a mistake while entering a name Dialing from the DirectoryTo search for a name by initial Index tablePress Ö Next key Add a number to the current number Editing4567890 IH G=Next 12344567890 Jane WalkerHelen Clear? =No CLEAR=Yes ErasingMaking Intercom Calls IntercomTo page the base unit, press To page another handsetTo page all handsets, press Handset LOCATOR/INTERCOM ALL Answering Intercom CallsDuring an intercom call Auto TalkTo transfer a call from the handset Transferring a CallCall Share Conference CallsEx. a conference call with Handset 1 To join a conversation Call ShareFor Call Waiting Service Users Special FeaturesTemporary Tone Dialing Muting Your ConversationFlash Button How to Use the Pause ButtonFor PBX Line/Long Distance Calls Selecting the flash timeRinger Tone Special FeaturesIncoming Call Tone Select the desired ringer tone by pressingAutomatic Answering Operation Setting the Unit to Answer CallsMonitoring incoming calls Press ANSWER!ON to turn on the Answering SystemTo play back messages Listening to MessagesDuring playback Erasing MessagesErasing a specific message Erasing all messagesTo listen to messages Remote Operation with the HandsetVoice menu Scroll to Message play by pressing Ö orALL Message Playback Direct commandsSummary of remote operation Remote Operation from a Touch Tone PhoneRemote Code Enter a remote code using a 2-digit number Press á Save keyTo check the remote code Remote code 11 H=Save 35 H=SaveRemote Operation from a Touch Tone Phone Voice MenuShaded parts are voice prompts Turning on the Answering System Direct Remote OperationSkipping the greeting message Call your unit and wait for 15 ringsWall Mounting To charge the handset battery Wall Mounting Adding Another PhoneBattery Replacement Date and time HInitial set Set answering HHS register Canceling the Handset RegistrationScroll to Deregistration by pressing Ö or Ñ Registration HDeregistrationBase unit Re-registering the HandsetHandset If the Following Appear Base unit. To cancel another handset When trying to store an item in the directory,Directory memory is full. To erase other items From the directory, seeCordless Telephone Problem TroubleshootingTo page. Try again later Problem Cause & RemedyConference call, you cannot Handset or the base unit. Try again laterAnswering System Problem Cause & Remedy TroubleshootingGeneral Problem Clean the charge contacts and charge again Battery has been discharged. Charge the battery fully pCurrently registered to another base unit For KX-TG2382B/KX-TG2382PWImportant Safety Instructions FCC and Other Information Important Safety InstructionsUseful Information FCC and Other Information Index Battery ChargeIndex SpecificationsLimited Warranty Coverage Panasonic Telephone Products Limited WarrantyCustomer Services Directory When you ship the product For product serviceFor your future reference Serial No Date of purchase
Top Page Image Contents