Panasonic KX-TCD950E-B operating instructions Adding Another Phone

Page 71

Caution:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1.Use only the battery specified.

2.Do not dispose of the battery in a fire. It may explode. Check with local waste management codes for special disposal instructions.

3.Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

4.Exercise care in handling the battery in order not to short the battery to conductive materials such as rings, bracelets, and keys. The battery and/or conductor may overheat and cause burns.

5.Charge the battery provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

•See "Important Notice Concerning the Correct Use and Charging of a Ni-MH Battery" on p. 77.

Adding Another Phone

This unit will not function during a power failure. To connect a standard telephone on the same line, use a T-adaptor.

To B.T. Socket

T-Adaptor

Telephone Line Cord

Useful Information Chapter 5

Standard Telephone

71

Image 71

Contents Operating Instructions Charge the battery for about 3 hours before initial useMethod of connection Important InformationRinger Equivalence Number REN Page Included with this unit Before Initial UseFor your future reference Radio waves. For maximum distance and noise free operation, Battery ChargeFor Best Performance Operating Distance/Noise EliminationContents Correct Use and Charging of a For Optional Multi-HandsetFor Optional Multi-KX-TCD950E-B Base unit Location of ControlsHandset Handset display Location of ControlsCharacters SymbolsConnections SettingsInstalling the Battery in the Handset Connection of Power Supply Recharge Battery strengthDisplay prompt Battery strength Operation Approx. battery life Battery informationTurning the Power on Are displayed Selecting the Dialling ModeSettings To remove the handset clip Installing the Handset ClipMaking Calls To redial the last number To dial after confirming the entered numberTo clear all numbers in the redial memory, press Program To redial after confirming the numbers in redial memoryAnswering Calls Setting the Receiver Volume Setting the Ringer Volume Memory sticker Automatic DiallingStoring Phone Numbers in Memory To erase a stored number I23To dial after confirming the phone number Dialling a Stored NumberSetting the pause timing Special FeaturesHow to Use the Pause Button For Analogue PBX Line/Long Distance Service UsersTo reject the waiting call Using the Recall FeatureTo hold the existing call and accept the waiting call To accept the waiting call and hang up the existing callSetting the FLASH/EARTH mode Handset Locator Setting the Key LockCancelling the key lock Helpful hints for programming Summary of Programming FeaturesBase unit program mode has the following functions Handset program mode has the following functionsOn the handset Setting the PasswordOn the base unit Call Prohibition Setting the Call Prohibition ModeCancelling the call prohibition mode Call Restriction Cancelling the call restriction numbers Cancelling the call restricted handsetsDirect Call Setting the Direct Call ModeCancelling the direct call mode Selecting the Talk Mode Display Setting the Key Tones Setting the Ringer PatternSetting the Range Warning Alarm OFF Clearing the Settings in MemoryClearing the Settings in Memory Operating More than One Handset For Optional Multi-Handset UsersRegistering a Handset in the Base Unit Press the desired base unit number using buttons 1 to Cancelling a Handset Cancelling a base unit Selecting the Stand-by Mode Display Selecting the handsets p Bell SelectionAll handsets p Cyclic pSelecting Cyclic Selecting the Handsets 23456 Selecting the First HandsetMulti-Unit User Selecting All HandsetsIntercom between Handsets Paging All Handsets from the Base UnitTransferring a Call from One Handset to Another Transferring a call using the intercomTransferring a call without an intercom ConferenceSetting the Call Waiting Tone Operation example Operating More than One Base UnitConnecting several base units to a PBX Organizing multiple handsets at more than one base unit For Optional Multi-KX-TCD950E-B UsersMulti-Unit User Registering at More than One Base Unit Press the desired base unit number using For Optional Multi-KX-TCD950E-B Users Specified base unit access Accessing the Base UnitAutomatic base unit access To charge the new battery after battery replacement Replacing the BatteryAdding Another Phone Before Requesting Help ProblemProblem Remedy Before Requesting Help Useful Information Chapter Placement Safety InstructionsSafety Installations EnvironmentUseful Information Chapter Dect Term DefinitionsModel No. KX-TCD950E-B Panasonic Business Systems U.KPQQX12030ZA-UK DU0798MK0 Sales Department Panasonic Business Systems U.KManufacturer