Panasonic KX-TCD700NL operating instructions Displays, Handset Display, Icons, Symbols Used

Page 11

30401 English KX-TCD700NL 25/4/01 2:32 pm Page 11

Displays

Handset Display

888888888888.

ÂÊ Á Ë È Í Î Ï  Ô Ó Ò

(The display shows all possible configurations)

Icons

ÎThe in-range icon indicates that the handset is in range of the base unit. It flashes when the handset is out of range.

ÏThe page/intercom icon is displayed when paging or using the intercom. It flashes when another unit pages the handset.

The talk icon is displayed when making or answering calls. It flashes when an outside call is being received.

ËThe direct call icon is displayed when this mode is turned on.

ÔThe call prohibition icon is displayed when this mode is turned on.

ÂThe program icon indicates that the unit is in the programming mode.

ÈThe ringer off icon indicates that ringer tone is temporarily turned OFF.

ÒThe battery icon indicates the battery strength.

ÓThe Key Lock icon is displayed when key lock is set on the handset. In this mode, keypad is disabled.

ÁThe speed dial icon is displayed when this mode is turned on.

LCD

Note: The LCD on your handset is a 7 segment display and each character will be displayed as shown in the table above. Some displayed characters differ e.g. character M is displayed as m. This is not a fault of the display and is normal display condition.

Symbols Used

Zshows that you should press the following key(s).

11

Image 11

Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Accessories includedEnvironment Safety InstructionsContents Programmable Functions On Programmable Functions Useful Information On the Base UnitConnections Getting StartedBattery Information Installing the Batteries in the HandsetBattery Charge Battery StrengthGetting Started Battery CautionBattery Replacement Remember to charge the new batteries after replacement seeWall Mounting Handset Location of ControlsBase Unit Icons Symbols UsedDisplays Handset DisplayBasic Start-up Operations To Redial after Confirming the Numbers in Redial Memory Making CallsTo Dial after Confirming the Entered Number To Redial the Last Number DialledDirect Call To Select the Receiver VolumeMaking Calls To Edit/Clear Numbers in the Redial ListLighted Handset Keypad Answering CallsAuto Talk To Turn the Handset Ringer Off TemporarilyDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory S U to select no Speed Dial MenuY to save number Speed DiallingSaving Numbers in Speed Dial List save speed Display number to be savedChecking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Sub-Menu Caller ID ServiceTo exit the list, Z W or P Using the Caller ListViewing the Caller List Operating More than One Handset Using the Caller ListFor Optional Multi-Unit Users Calling Back from the Caller ListTransferring a Call from One Handset to Another Paging/IntercomPaging All Handsets from the Base Unit Intercom between HandsetsConference Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom Using the Recall Feature Special FeaturesHow to Use the Pause Feature Y for more than 2 seconds Special FeaturesSetting the Key Lock on To Cancel the Key LockOn the Handset Summary of Programmable FunctionsSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm 25/4/01 232 pm Set Key Confirmation Tone ON/OFF key tone on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Battery Low Tone ON/OFF battery low on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Direct Call ON/OFF set direct on/off see Setting Call OptionSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs. a confirmation tone sounds RegistrationRegistering a Handset to a Base Unit register hs ZV or Y Cancelling a Base Unit cancel baseSelect Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base1 Function Initial Setting Reset Handset reset hsBell Selection Programmable Functions On the Base UnitSetting the Clock To Select the Base Unit Ringer VolumeSelect Pause Timing Select Earth/Flash ModeProgrammable Functions On the Base Unit Set Base Unit PIN Cancelling a HandsetOr U Call RestrictionStoring the Carrier Code Automatic Route SelectionStoring the Area Code To turn the international code 00 delete mode ON/OFF Using International Carrier servicesFunction Initial Setting Reset Base UnitOption Covers Option Covers Using the Belt ClipBefore Requesting Help Problem RemedyBefore Requesting Help Problem Remedy Garantiebewijs English KX-TCD700NL 25/4/01 232 pm Sales department Manufacturers Declaration