Panasonic KX-TCD700NL Getting Started, Battery Caution, Battery Replacement, Base Unit Location

Page 8

30401 English KX-TCD700NL 25/4/01 2:32 pm Page 8

➡Getting Started

Battery Caution:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1.Use only the batteries specified.

2.Do not use non-rechargeable batteries.

3.Do not mix old and new batteries.

4.Do not dispose of the batteries in a fire, they may explode. Check with local waste management codes for special disposal instructions.

5.Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

6.Exercise care in handling the batteries in order not to short the batteries with conductive materials such as rings, bracelets, and keys. The batteries and/or conductor may overheat and cause burns.

7.Charge the batteries provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

•Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

NL Niet weggooien,

maar inleveren

als KCA.

Battery Replacement

If “Û” flashes after a few telephone calls even when the handset batteries have been fully charged, it is time to replace the batteries with new ones.

Remember to charge the new batteries after replacement (see page 7).

•Discard defective batteries as soon as possible. Defective batteries may leak into the unit.

Base Unit Location

For maximum distance and noise-free operation, the recommended base unit location is:

•Away from electrical appliances such as TV, radio, personal computer or another telephone.

•In a convenient high and central location.

8

Image 8

Contents Operating Instructions Charge the batteries for approx hours before initial useAccessories included Dear purchaserSafety Instructions EnvironmentContents Programmable Functions Useful Information On the Base Unit Programmable Functions OnGetting Started ConnectionsInstalling the Batteries in the Handset Battery ChargeBattery Strength Battery InformationBattery Caution Battery ReplacementRemember to charge the new batteries after replacement see Getting StartedWall Mounting Handset Location of ControlsBase Unit Symbols Used DisplaysHandset Display IconsBasic Start-up Operations Making Calls To Dial after Confirming the Entered NumberTo Redial the Last Number Dialled To Redial after Confirming the Numbers in Redial MemoryTo Select the Receiver Volume Making CallsTo Edit/Clear Numbers in the Redial List Direct CallAnswering Calls Auto TalkTo Turn the Handset Ringer Off Temporarily Lighted Handset KeypadDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory Speed Dial Menu S U to select noSpeed Dialling Saving Numbers in Speed Dial List save speedDisplay number to be saved Y to save numberChecking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Service Caller ID Sub-MenuTo exit the list, Z W or P Using the Caller ListViewing the Caller List Using the Caller List For Optional Multi-Unit UsersCalling Back from the Caller List Operating More than One HandsetPaging/Intercom Paging All Handsets from the Base UnitIntercom between Handsets Transferring a Call from One Handset to AnotherConference Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom Using the Recall Feature Special FeaturesHow to Use the Pause Feature Special Features Setting the Key Lock onTo Cancel the Key Lock Y for more than 2 secondsSummary of Programmable Functions On the HandsetSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm 25/4/01 232 pm Setting Tone Options Set Range Warning Alarm ON/OFF range alarm on/offSet Battery Low Tone ON/OFF battery low on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Direct Call ON/OFF set direct on/off see Setting Call OptionSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs. a confirmation tone sounds RegistrationRegistering a Handset to a Base Unit register hs Cancelling a Base Unit cancel base ZV or YSelect Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base1 Reset Handset reset hs Function Initial SettingProgrammable Functions On the Base Unit Bell SelectionTo Select the Base Unit Ringer Volume Setting the ClockSelect Pause Timing Select Earth/Flash ModeProgrammable Functions On the Base Unit Cancelling a Handset Set Base Unit PINCall Restriction Or UAutomatic Route Selection Storing the Carrier CodeStoring the Area Code Using International Carrier services To turn the international code 00 delete mode ON/OFFReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Option CoversProblem Remedy Before Requesting HelpBefore Requesting Help Problem Remedy Garantiebewijs English KX-TCD700NL 25/4/01 232 pm Manufacturers Declaration Sales department