Panasonic KX-TCD700NL operating instructions Using the Belt Clip, Option Covers

Page 50

30401 English KX-TCD700NL 25/4/01 2:32 pm Page 50

➡Option Covers

4.Place the new option cover fitting the tabs on the cover into their slots on the handset.

5.Snap the option cover shut on the lower ➀, middle ➁ and upper ➂ parts of the handset.

Tabs

Slot

Slot

3

3 2

2

1

1

6.Connect the batteries and close the battery cover.

Using the Belt Clip

You can hang the handset on your belt or pocket using the belt clip.

To remove the belt clip

50

Image 50

Contents Operating Instructions Charge the batteries for approx hours before initial useAccessories included Dear purchaserSafety Instructions EnvironmentContents Programmable Functions Useful Information On the Base Unit Programmable Functions OnGetting Started ConnectionsBattery Strength Installing the Batteries in the HandsetBattery Charge Battery InformationRemember to charge the new batteries after replacement see Battery CautionBattery Replacement Getting StartedWall Mounting Handset Location of ControlsBase Unit Handset Display Symbols UsedDisplays IconsBasic Start-up Operations To Redial the Last Number Dialled Making CallsTo Dial after Confirming the Entered Number To Redial after Confirming the Numbers in Redial MemoryTo Edit/Clear Numbers in the Redial List To Select the Receiver VolumeMaking Calls Direct CallTo Turn the Handset Ringer Off Temporarily Answering CallsAuto Talk Lighted Handset KeypadDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory Speed Dial Menu S U to select noDisplay number to be saved Speed DiallingSaving Numbers in Speed Dial List save speed Y to save numberChecking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Service Caller ID Sub-MenuTo exit the list, Z W or P Using the Caller ListViewing the Caller List Calling Back from the Caller List Using the Caller ListFor Optional Multi-Unit Users Operating More than One HandsetIntercom between Handsets Paging/IntercomPaging All Handsets from the Base Unit Transferring a Call from One Handset to AnotherConference Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom Using the Recall Feature Special FeaturesHow to Use the Pause Feature To Cancel the Key Lock Special FeaturesSetting the Key Lock on Y for more than 2 secondsSummary of Programmable Functions On the HandsetSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm 25/4/01 232 pm Set Battery Low Tone ON/OFF battery low on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Direct Call ON/OFF set direct on/off see Setting Call OptionSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs. a confirmation tone sounds RegistrationRegistering a Handset to a Base Unit register hs Cancelling a Base Unit cancel base ZV or YSelect Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base1 Reset Handset reset hs Function Initial SettingProgrammable Functions On the Base Unit Bell SelectionTo Select the Base Unit Ringer Volume Setting the ClockSelect Pause Timing Select Earth/Flash ModeProgrammable Functions On the Base Unit Cancelling a Handset Set Base Unit PINCall Restriction Or UAutomatic Route Selection Storing the Carrier CodeStoring the Area Code Using International Carrier services To turn the international code 00 delete mode ON/OFFReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Option CoversProblem Remedy Before Requesting HelpBefore Requesting Help Problem Remedy Garantiebewijs English KX-TCD700NL 25/4/01 232 pm Manufacturers Declaration Sales department