Panasonic KX-TCD700NL operating instructions Before Requesting Help, Problem Remedy

Page 51

30401 English KX-TCD700NL 25/4/01 2:32 pm Page 51

Before Requesting Help

Problem

Remedy

 

 

The unit does not work.

Turn the power ON (p.12).

Check the settings.

Charge the batteries fully (p.7).

Clean the charge contacts and charge again (p.7).

Unplug the AC adaptor and turn the power OFF to reset. Plug in the AC adaptor and turn the power ON. Then try again.

The handset has been cancelled or has not been registered. Register the handset (p.36).

Re-install the handset batteries and try again.

Δ flashes and an alarm tone

• You are too far from the base unit. Move closer and

sounds when you Z O.

try again.

 

• Plug in the AC adaptor.

 

 

A busy tone sounds when you Z O.

• Another handset is in use.

You cannot dial.

• The unit is in call prohibition mode. Cancel the mode

 

(p.33).

 

• The dialled number is restricted. Cancel the number

 

(p.44).

 

• Key lock mode is set. Cancel the mode (p.26).

 

 

Δ flashes during a conversation

• The handset is out of range. Move closer to the

and the call is disconnected.

base unit and make the call again.

 

• Plug in the AC adaptor.

 

 

Static, sound cuts in/out, fades.

• Locate the handset and base unit away from other

Interference from other electrical

electrical appliances.

units.

• Move closer to the base unit.

 

 

The handset does not ring.

Turn the power ON (p.12).

The ringer is set to OFF. Select the desired volume level (p.29).

The base unit does not ring.

The ringer is set to OFF. Set to HIGH, MEDIUM or LOW (p.41).

You cannot program function items

• Programming is not possible while the unit is in the

such as the handset ringer volume.

talk or intercom mode.

 

• Do not pause for over 60 seconds while

 

programming.

 

 

You cannot store a phone number

• You cannot store a phone number while the unit is

in memory.

in the talk or intercom mode.

 

• Do not pause for over 60 seconds while storing.

51

Image 51
Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Accessories includedEnvironment Safety InstructionsContents Programmable Functions On Programmable Functions Useful Information On the Base UnitConnections Getting StartedBattery Information Installing the Batteries in the HandsetBattery Charge Battery StrengthGetting Started Battery CautionBattery Replacement Remember to charge the new batteries after replacement seeWall Mounting Location of Controls Base UnitHandset Icons Symbols UsedDisplays Handset DisplayBasic Start-up Operations To Redial after Confirming the Numbers in Redial Memory Making CallsTo Dial after Confirming the Entered Number To Redial the Last Number DialledDirect Call To Select the Receiver VolumeMaking Calls To Edit/Clear Numbers in the Redial ListLighted Handset Keypad Answering CallsAuto Talk To Turn the Handset Ringer Off TemporarilySpeed Dialling Storing Phone Numbers in MemoryDialling a Stored Number S U to select no Speed Dial MenuY to save number Speed DiallingSaving Numbers in Speed Dial List save speed Display number to be savedCaller ID Service How Caller Information is Displayed when a Call is ReceivedChecking the Number of New Calls Caller ID Sub-Menu Caller ID ServiceUsing the Caller List Viewing the Caller ListTo exit the list, Z W or P Operating More than One Handset Using the Caller ListFor Optional Multi-Unit Users Calling Back from the Caller ListTransferring a Call from One Handset to Another Paging/IntercomPaging All Handsets from the Base Unit Intercom between HandsetsHandset 1 Z P Handset 2 When the unit rings, Z O to answer Paging/IntercomConference Special Features How to Use the Pause FeatureUsing the Recall Feature Y for more than 2 seconds Special FeaturesSetting the Key Lock on To Cancel the Key LockOn the Handset Summary of Programmable FunctionsSetting Time Alarm Function To Stop the AlarmSet Time of Alarm set time 25/4/01 232 pm Set Key Confirmation Tone ON/OFF key tone on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Battery Low Tone ON/OFF battery low on/offSetting Display Options Select the Standby Mode Display standby modeSelect the Talk Mode Display talk mode Setting Call Option Set Call Prohibition call bar seeSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Setting Other Options Select Battery Type battery typeSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registration Registering a Handset to a Base Unit register hsHold Ï on base unit for 10 secs. a confirmation tone sounds ZV or Y Cancelling a Base Unit cancel baseAutomatic Base Unit Access auto Specified Base Unit Access eg. base1Select Base Unit select bs Function Initial Setting Reset Handset reset hsBell Selection Programmable Functions On the Base UnitSetting the Clock To Select the Base Unit Ringer VolumeSelect Earth/Flash Mode Programmable Functions On the Base UnitSelect Pause Timing Set Base Unit PIN Cancelling a HandsetOr U Call RestrictionStoring the Carrier Code Automatic Route SelectionStoring the Area Code To turn the international code 00 delete mode ON/OFF Using International Carrier servicesFunction Initial Setting Reset Base UnitOption Covers Option Covers Using the Belt ClipBefore Requesting Help Problem RemedyBefore Requesting Help Problem Remedy Garantiebewijs English KX-TCD700NL 25/4/01 232 pm Sales department Manufacturers Declaration