Panasonic KX-TCD700NL Programmable Functions On the Base Unit, Select Earth/Flash Mode

Page 42

30401 English KX-TCD700NL 25/4/01 2:32 pm Page 42

➡Programmable Functions (On the Base Unit)

Select Earth/Flash Mode

The earth relay can be installed as an option depending on your PBX requirements. Please consult your nearest Panasonic Service Centre for installation. Then you can select the flash or earth mode. The factory pre-set is Flash.

Select Pause Timing

You can set the pause timing to 3 or 5 seconds, depending on your PBX requirements. The factory pre-set is 3 seconds.

(Standby Mode)

-1-888888801

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z

Yor V

new speed

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z

Sor U

setting bs

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z

Yor V

input code

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•Select Earth.

Z C

•Enter PIN (4 digits)

Z B

3221

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•Current setting is displayed. 1 = Flash

2 = Earth

Z B

3222

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

eg. Earth is selected.

Z Y or V

setting bs

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•A confirmation tone sounds.

•Display returns to function menu.

•Select Flash Timing.

Z C

•Enter PIN (4 digits)

Z B

3222

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•Earth is selected.

Current setting is displayed.

Z A to select Flash. (If Flash is already selected

ZY).

3221-2

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•Current setting is displayed. 1=Flash 1 (700m sec) 2=Flash 2 (110m sec)

Z A - B to select Flash time.

3221-1

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

eg. Flash 1 is selected.

Z Y or V

setting bs

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•A confirmation tone sounds.

•Display returns to function menu.

•Select Pause Timing.

Z C

•Enter PIN (4 digits)

Z C

33-123456

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•3 seconds is selected.

Z A or B to select Pause time.

eg.

1 = 3 seconds

2 = 5 seconds.

Z Y or V

setting bs

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•A confirmation tone sounds.

•Display returns to function menu.

42

Image 42

Contents Operating Instructions Charge the batteries for approx hours before initial useAccessories included Dear purchaserSafety Instructions EnvironmentContents Programmable Functions Useful Information On the Base Unit Programmable Functions OnGetting Started ConnectionsBattery Strength Installing the Batteries in the HandsetBattery Charge Battery InformationRemember to charge the new batteries after replacement see Battery CautionBattery Replacement Getting StartedWall Mounting Location of Controls Base UnitHandset Handset Display Symbols UsedDisplays IconsBasic Start-up Operations To Redial the Last Number Dialled Making CallsTo Dial after Confirming the Entered Number To Redial after Confirming the Numbers in Redial MemoryTo Edit/Clear Numbers in the Redial List To Select the Receiver VolumeMaking Calls Direct CallTo Turn the Handset Ringer Off Temporarily Answering CallsAuto Talk Lighted Handset KeypadSpeed Dialling Storing Phone Numbers in MemoryDialling a Stored Number Speed Dial Menu S U to select noDisplay number to be saved Speed DiallingSaving Numbers in Speed Dial List save speed Y to save numberCaller ID Service How Caller Information is Displayed when a Call is ReceivedChecking the Number of New Calls Caller ID Service Caller ID Sub-MenuUsing the Caller List Viewing the Caller ListTo exit the list, Z W or P Calling Back from the Caller List Using the Caller ListFor Optional Multi-Unit Users Operating More than One HandsetIntercom between Handsets Paging/IntercomPaging All Handsets from the Base Unit Transferring a Call from One Handset to AnotherHandset 1 Z P Handset 2 When the unit rings, Z O to answer Paging/IntercomConference Special Features How to Use the Pause FeatureUsing the Recall Feature To Cancel the Key Lock Special FeaturesSetting the Key Lock on Y for more than 2 secondsSummary of Programmable Functions On the HandsetSetting Time Alarm Function To Stop the AlarmSet Time of Alarm set time 25/4/01 232 pm Set Battery Low Tone ON/OFF battery low on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Key Confirmation Tone ON/OFF key tone on/offSetting Display Options Select the Standby Mode Display standby modeSelect the Talk Mode Display talk mode Setting Call Option Set Call Prohibition call bar seeSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Setting Other Options Select Battery Type battery typeSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registration Registering a Handset to a Base Unit register hsHold Ï on base unit for 10 secs. a confirmation tone sounds Cancelling a Base Unit cancel base ZV or YAutomatic Base Unit Access auto Specified Base Unit Access eg. base1Select Base Unit select bs Reset Handset reset hs Function Initial SettingProgrammable Functions On the Base Unit Bell SelectionTo Select the Base Unit Ringer Volume Setting the ClockSelect Earth/Flash Mode Programmable Functions On the Base UnitSelect Pause Timing Cancelling a Handset Set Base Unit PINCall Restriction Or UAutomatic Route Selection Storing the Carrier CodeStoring the Area Code Using International Carrier services To turn the international code 00 delete mode ON/OFFReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Option CoversProblem Remedy Before Requesting HelpBefore Requesting Help Problem Remedy Garantiebewijs English KX-TCD700NL 25/4/01 232 pm Manufacturers Declaration Sales department