Panasonic KX-TCD700NL Making Calls, To Dial after Confirming the Entered Number

Page 13

30401 English KX-TCD700NL 25/4/01 2:32 pm Page 13

Making Calls

Note: for basic making calls operation, see page 12.

To Dial after Confirming the Entered Number

With this feature you are able to confirm the entered number before you start dialling.

1.Dial a Phone Number

If number is not entered correctly: To clear one digit, Z W briefly. To clear all digits, Z and hold W.

2.Phone number confirmed, Z O

(After a few seconds, the length of call is displayed).

3.To end call, Z P.

(After a few seconds, the display returns to the standby mode).

0123456789

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

0123456789

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

00-00-31

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

-1-œœœœœœœ02

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Chapter 2

Note: If Î flashes and an alarm tone sounds after pressing O, move closer to the base unit. Then try again.

To Redial the Last Number Dialled

1. Z O

2.Z X

(The last number dialled is displayed and automatically redialled).

• After a few seconds, the length of call is displayed.

0123456789

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

00-00-00

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

To Redial after Confirming the Numbers in Redial Memory

The unit automatically stores the last 10 numbers dialled into redial memory.

1. Z X

 

0123456789

(The last number dialled is displayed).

Â Ê Á Ë È Í

 

Î Ï  Ô Ó Ò

 

 

2.Z S or U to select required number (To exit the list, Z W).

3. Z O

00-00-00

Â Ê Á Ë È Í

(After a few seconds the length of call is displayed).

Î Ï Ô Ó Ò

 

 

13

Image 13
Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Accessories includedEnvironment Safety InstructionsContents Programmable Functions On Programmable Functions Useful Information On the Base UnitConnections Getting StartedBattery Charge Installing the Batteries in the HandsetBattery Strength Battery InformationBattery Replacement Battery CautionRemember to charge the new batteries after replacement see Getting StartedWall Mounting Base Unit Location of ControlsHandset Displays Symbols UsedHandset Display IconsBasic Start-up Operations To Dial after Confirming the Entered Number Making CallsTo Redial the Last Number Dialled To Redial after Confirming the Numbers in Redial MemoryMaking Calls To Select the Receiver VolumeTo Edit/Clear Numbers in the Redial List Direct CallAuto Talk Answering CallsTo Turn the Handset Ringer Off Temporarily Lighted Handset KeypadStoring Phone Numbers in Memory Speed DiallingDialling a Stored Number S U to select no Speed Dial MenuSaving Numbers in Speed Dial List save speed Speed DiallingDisplay number to be saved Y to save numberHow Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Caller ID Sub-Menu Caller ID ServiceViewing the Caller List Using the Caller ListTo exit the list, Z W or P For Optional Multi-Unit Users Using the Caller ListCalling Back from the Caller List Operating More than One HandsetPaging All Handsets from the Base Unit Paging/IntercomIntercom between Handsets Transferring a Call from One Handset to AnotherPaging/Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerConference How to Use the Pause Feature Special FeaturesUsing the Recall Feature Setting the Key Lock on Special FeaturesTo Cancel the Key Lock Y for more than 2 secondsOn the Handset Summary of Programmable FunctionsTo Stop the Alarm Setting Time Alarm FunctionSet Time of Alarm set time 25/4/01 232 pm Set Range Warning Alarm ON/OFF range alarm on/off Setting Tone OptionsSet Battery Low Tone ON/OFF battery low on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Standby Mode Display standby mode Setting Display OptionsSelect the Talk Mode Display talk mode Set Call Prohibition call bar see Setting Call OptionSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Select Battery Type battery type Setting Other OptionsSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registering a Handset to a Base Unit register hs RegistrationHold Ï on base unit for 10 secs. a confirmation tone sounds ZV or Y Cancelling a Base Unit cancel baseSpecified Base Unit Access eg. base1 Automatic Base Unit Access autoSelect Base Unit select bs Function Initial Setting Reset Handset reset hsBell Selection Programmable Functions On the Base UnitSetting the Clock To Select the Base Unit Ringer VolumeProgrammable Functions On the Base Unit Select Earth/Flash ModeSelect Pause Timing Set Base Unit PIN Cancelling a HandsetOr U Call RestrictionStoring the Carrier Code Automatic Route SelectionStoring the Area Code To turn the international code 00 delete mode ON/OFF Using International Carrier servicesFunction Initial Setting Reset Base UnitOption Covers Option Covers Using the Belt ClipBefore Requesting Help Problem RemedyBefore Requesting Help Problem Remedy Garantiebewijs English KX-TCD700NL 25/4/01 232 pm Sales department Manufacturers Declaration