Panasonic KX-TCD951EB Registration, F7 iU, F7 io, Registering a Handset in the Base Unit

Page 31

Registration

Registering a Handset in the Base Unit

You must register the handset in the base unit before use.

Charge the optional handset batteries for about 4 hours before initial use.

Make sure that the power is ON (p. 12) and the unit is in the stand-by mode.

Register the handset number within 1 minute. If not registered within 1 minute, press PROG on the handset to cancel the programming mode. Then start again from step 1.

1Base unit where handset is to be

registered:

Press and hold on the base unit for more than 10 seconds until the in

use indicator ( ) lights and a confirmation tone sounds.

2Handset: Press PROG .

3Press G or F until “F7 i ” is displayed.

4Press O K .

The available base unit numbers are displayed.

F7 iU i234

5 Press the desired base unit number 1 to 4 .

The number is assigned as the base unit number for the handset.

While the handset is searching for the base unit, “- ” flashes across on the display.

6Enter the base unit password (p. 23).

F7 io - - - -

7Press PROG .

A confirmation tone sounds and the display will return to the stand-by mode.

The in use indicator ( ) on the base unit will go out.

To register the handset in more than one base unit, repeat from step 1 with the other base unit(s).

The base unit number which the handset is currently in contact with can be displayed in the stand-by mode (p. 34). Calls (both incoming and outgoing) can be conducted only via the displayed base unit (even if the radio areas overlap with neighbouring base units).

Multi-Unit User Operations Chapter 4

-

31

Image 31
Contents Charge the batteries for about 4 hours before initial use Operating InstructionsRinger Equivalence Number REN Important InformationMethod of connection Page Before Initial Use For Best Performance Battery ChargeBase Unit Location Contents Correct Use and Charging Selecting the Stand-by ModeBase unit Location of ControlsHandset Icons SettingsInstalling the Batteries in the Handset DisplayUSE only with Panasonic AC Adaptor KX-TCA9E or KX-TCA11E Settings ConnectionsHooks To Mains Outlet AC 230-240 V, 50 Hz Telephone Line CordFully charged Medium Low Battery strengthBattery information RechargeCurrent connected base unit number is displayed Settings Turning the Power onDisplay Power Button PWR Press P W RPress Selecting the Dialling ModePress Prog then I N T Enter the base unit password Ensure that the dialling mode is selected toneRinger pattern Settings Selecting the Handset Ringer Volume/PatternRinger volume F23UPress Prog then I N T Press 2 Twice Selecting the Base Unit Ringer VolumePress the desired volume level 1 , 2 , 3 or 22u2888800 00 To select the receiver volumeMaking Calls I2345678To turn the handset ringer off temporarily Answering CallsTo redial the last number dialled To redial after confirming the numbers in redial memoryTo erase a stored number Speed DiallingStoring Phone Numbers in Memory Dialling a Stored NumberPress Prog then I N T Enter the base unit password p Special FeaturesHow to Use the Pause Feature Setting the pause timingTo cancel the key lock Special Features Handset LocatorSetting the Key Lock For Rotary or Pulse Service UsersTo accept the waiting call and hang up the existing call Using the Recall FeatureSelecting the earth option/time break recall mode 32uSummary of Programmable Functions 5o - - o Setting the PasswordF5o F5o - - oF42 Setting the Direct Call ModeTo turn OFF the direct call mode Direct CallF4 IO0 To turn OFF the call prohibition modeCall Prohibition F4 IoCall Restriction To cancel the call restricted handsetsTo cancel the call restriction numbers When you dial a restricted numberF26U Other Programmable SettingsF2 iU F25U0I234567890 Other Programmable Settings Selecting the Talk Mode DisplayPress G or F to select to select the desired setting F32UFunction Clearing the Settings in MemoryOperating More than One Handset For Optional Multi-Unit UsersOperating More than One Base Unit Registering a Handset in the Base Unit RegistrationF7 iU F7 ioI000 Registration Selecting the Base Unit AccessAutomatic base unit access Specified base unit accessPress O K Enter the handset password p Cancelling a HandsetCancelling a base unit Enter the handset numbers you want to cancelIu2 Selecting the Stand-by Mode DisplayBell Selection F3 i0Selecting all handsets Iu3I03 i23456 Selecting first handsetIntercom between Handsets Paging/Intercom888800 00 0 Paging All Handsets from the Base UnitTransferring a Call from One Handset to Another Transferring a call using the intercomTransferring a call without the intercom Press Prog Press G or F until F24 is displayed Press O K Setting the Call Waiting ToneF24U Paging/Intercom ConferenceReplaceshown. the batteries with new ones as Replacing the BatteriesReplacing the Batteries Using the Belt ClipTo remove the belt clip Before Requesting Help Problem RemedyUnit does not work You cannot redial Be included when rediallingBefore Requesting Help Does not functionYou cannot register the handset in the base unit Placement Safety InstructionsSafety Installations EnvironmentAdding Another Phone Term Definitions Serial No Panasonic Business Systems U.KReceipt No Date of Purchase Model No. KX-TCD951EBManufacturer Sales Department Panasonic Business Systems U.KPQQX12191ZB-UK WU0699MK2079