Panasonic KX-TCD951EB operating instructions Adding Another Phone

Page 45

Adding Another Phone

This unit will not function during a power failure. To connect a standard telephone on the same line, use a T-adaptor.

To B.T. Socket

T-Adaptor

Telephone Line Cord

Standard Telephone

Important Notice Concerning the Correct Use and Charging of Ni-Cd (Ni-MH) Batteries

Batteries, due to their construction, undergo some wear and tear. The lifetime of a battery also depends on correct maintenance. Charging and discharging are the most important factors. You should take notice of the following to maintain the life of the battery as long as possible.

Ni-Cd (Ni-MH) batteries may experience a memory effect. If fully charged batteries are used several times only for 15 minutes in the handset and then recharged, the capacity of the batteries will be reduced to 15 minutes due to the memory effect. Therefore you should discharge the

batteries completely, i.e. use them in the handset until “ ” on the display starts flashing. Then recharge them as described in the manual. After the memory effect has occurred, it is possible to achieve almost complete capacity of the Ni-Cd (Ni-MH) batteries by charging and discharging several times one after another.

Ni-Cd (Ni-MH) batteries can also self-discharge. This self-discharge depends on the ambient temperature. At temperatures under 0°C, the self-discharge will be the lowest. High humidity and high temperatures support the self-discharge. Also long-term storage will lead to self-discharge. A dead Ni-Cd (Ni-MH) battery should not be disposed of normally. They contain toxic heavy cadmium (metal hydride) and therefore should be recycled.

Useful Information Chapter 5

45

Image 45
Contents Charge the batteries for about 4 hours before initial use Operating InstructionsImportant Information Ringer Equivalence Number RENMethod of connection Page Before Initial Use Battery Charge For Best PerformanceBase Unit Location Contents Correct Use and Charging Selecting the Stand-by ModeLocation of Controls Base unitHandset Installing the Batteries in the Handset SettingsDisplay IconsHooks To Mains Outlet AC 230-240 V, 50 Hz Settings ConnectionsTelephone Line Cord USE only with Panasonic AC Adaptor KX-TCA9E or KX-TCA11EBattery information Battery strengthRecharge Fully charged Medium LowDisplay Power Button PWR Settings Turning the Power onPress P W R Current connected base unit number is displayedPress Prog then I N T Enter the base unit password Selecting the Dialling ModeEnsure that the dialling mode is selected tone PressRinger volume Settings Selecting the Handset Ringer Volume/PatternF23U Ringer patternPress the desired volume level 1 , 2 , 3 or Selecting the Base Unit Ringer Volume22u2 Press Prog then I N T Press 2 TwiceMaking Calls To select the receiver volumeI2345678 888800 00To redial the last number dialled Answering CallsTo redial after confirming the numbers in redial memory To turn the handset ringer off temporarilyStoring Phone Numbers in Memory Speed DiallingDialling a Stored Number To erase a stored numberHow to Use the Pause Feature Special FeaturesSetting the pause timing Press Prog then I N T Enter the base unit password pSetting the Key Lock Special Features Handset LocatorFor Rotary or Pulse Service Users To cancel the key lockSelecting the earth option/time break recall mode Using the Recall Feature32u To accept the waiting call and hang up the existing callSummary of Programmable Functions F5o Setting the PasswordF5o - - o 5o - - oTo turn OFF the direct call mode Setting the Direct Call ModeDirect Call F42Call Prohibition To turn OFF the call prohibition modeF4 Io F4 IO0To cancel the call restriction numbers To cancel the call restricted handsetsWhen you dial a restricted number Call RestrictionF2 iU Other Programmable SettingsF25U0 F26UPress G or F to select to select the desired setting Other Programmable Settings Selecting the Talk Mode DisplayF32U I234567890Function Clearing the Settings in MemoryFor Optional Multi-Unit Users Operating More than One HandsetOperating More than One Base Unit F7 iU RegistrationF7 io Registering a Handset in the Base UnitAutomatic base unit access Registration Selecting the Base Unit AccessSpecified base unit access I000Cancelling a base unit Cancelling a HandsetEnter the handset numbers you want to cancel Press O K Enter the handset password pBell Selection Selecting the Stand-by Mode DisplayF3 i0 Iu2I03 i23456 Iu3Selecting first handset Selecting all handsets888800 00 0 Paging/IntercomPaging All Handsets from the Base Unit Intercom between HandsetsTransferring a call using the intercom Transferring a Call from One Handset to AnotherTransferring a call without the intercom F24U Setting the Call Waiting TonePaging/Intercom Conference Press Prog Press G or F until F24 is displayed Press O KReplaceshown. the batteries with new ones as Replacing the BatteriesUsing the Belt Clip Replacing the BatteriesTo remove the belt clip Problem Remedy Before Requesting HelpUnit does not work Before Requesting Help Be included when rediallingDoes not function You cannot redialYou cannot register the handset in the base unit Safety Safety InstructionsInstallations Environment PlacementAdding Another Phone Term Definitions Receipt No Date of Purchase Panasonic Business Systems U.KModel No. KX-TCD951EB Serial NoSales Department Panasonic Business Systems U.K ManufacturerPQQX12191ZB-UK WU0699MK2079