Panasonic KX-TCD951EB operating instructions You cannot register the handset in the base unit

Page 43

Problem

Remedy

You cannot register the handset in the base unit.

The base unit has registered a maximum of 6 handsets or the handset has registered a maximum of 4 base units.

A wrong base unit password was entered. Enter the correct password.

There is interference from other electrical units. Locate the handset and base unit away from them.

You must finish registration within 1 minute after the ringer tone sounds, or programming will be cancelled (p. 31).

” flashes or the unit beeps every 15 seconds.

Charge the batteries fully (p. 11).

You charged the batteries fully, but

Clean the charge contacts and charge again (p. 11).

 

” flashes.

 

Install new batteries (p. 39, 45).

 

 

 

 

 

 

 

The charge indicator (

) light never

This is normal.

goes out while charging.

 

 

00

05

01

06

02

07

0308

0409

10

11

12

13

14

43

15

16

17

18

19

Image 43
Contents Charge the batteries for about 4 hours before initial use Operating InstructionsRinger Equivalence Number REN Important InformationMethod of connection Page Before Initial Use For Best Performance Battery ChargeBase Unit Location Contents Correct Use and Charging Selecting the Stand-by ModeBase unit Location of ControlsHandset Icons SettingsInstalling the Batteries in the Handset DisplayUSE only with Panasonic AC Adaptor KX-TCA9E or KX-TCA11E Settings ConnectionsHooks To Mains Outlet AC 230-240 V, 50 Hz Telephone Line CordFully charged Medium Low Battery strengthBattery information RechargeCurrent connected base unit number is displayed Settings Turning the Power onDisplay Power Button PWR Press P W RPress Selecting the Dialling ModePress Prog then I N T Enter the base unit password Ensure that the dialling mode is selected toneRinger pattern Settings Selecting the Handset Ringer Volume/PatternRinger volume F23UPress Prog then I N T Press 2 Twice Selecting the Base Unit Ringer VolumePress the desired volume level 1 , 2 , 3 or 22u2888800 00 To select the receiver volumeMaking Calls I2345678To turn the handset ringer off temporarily Answering CallsTo redial the last number dialled To redial after confirming the numbers in redial memoryTo erase a stored number Speed DiallingStoring Phone Numbers in Memory Dialling a Stored NumberPress Prog then I N T Enter the base unit password p Special FeaturesHow to Use the Pause Feature Setting the pause timingTo cancel the key lock Special Features Handset LocatorSetting the Key Lock For Rotary or Pulse Service UsersTo accept the waiting call and hang up the existing call Using the Recall FeatureSelecting the earth option/time break recall mode 32uSummary of Programmable Functions 5o - - o Setting the PasswordF5o F5o - - oF42 Setting the Direct Call ModeTo turn OFF the direct call mode Direct CallF4 IO0 To turn OFF the call prohibition modeCall Prohibition F4 IoCall Restriction To cancel the call restricted handsetsTo cancel the call restriction numbers When you dial a restricted numberF26U Other Programmable SettingsF2 iU F25U0I234567890 Other Programmable Settings Selecting the Talk Mode DisplayPress G or F to select to select the desired setting F32UFunction Clearing the Settings in MemoryOperating More than One Handset For Optional Multi-Unit UsersOperating More than One Base Unit Registering a Handset in the Base Unit RegistrationF7 iU F7 ioI000 Registration Selecting the Base Unit AccessAutomatic base unit access Specified base unit accessPress O K Enter the handset password p Cancelling a HandsetCancelling a base unit Enter the handset numbers you want to cancelIu2 Selecting the Stand-by Mode DisplayBell Selection F3 i0Selecting all handsets Iu3I03 i23456 Selecting first handsetIntercom between Handsets Paging/Intercom888800 00 0 Paging All Handsets from the Base UnitTransferring a Call from One Handset to Another Transferring a call using the intercomTransferring a call without the intercom Press Prog Press G or F until F24 is displayed Press O K Setting the Call Waiting ToneF24U Paging/Intercom ConferenceReplaceshown. the batteries with new ones as Replacing the BatteriesReplacing the Batteries Using the Belt ClipTo remove the belt clip Before Requesting Help Problem RemedyUnit does not work You cannot redial Be included when rediallingBefore Requesting Help Does not functionYou cannot register the handset in the base unit Placement Safety InstructionsSafety Installations EnvironmentAdding Another Phone Term Definitions Serial No Panasonic Business Systems U.KReceipt No Date of Purchase Model No. KX-TCD951EBManufacturer Sales Department Panasonic Business Systems U.KPQQX12191ZB-UK WU0699MK2079