Panasonic KX-TCD700BX operating instructions Location of Controls, Base Unit, Handset

Page 10

31939_KX-TCD700CX_Czech 18/6/01 1:54 pm Page 10

Location of Controls

Base Unit

Charge Contacts

Handset

Display

(Speed Dial) Button

O(Talk) Button

Navigator Key

(, , ,)

X(Redial/ Pause) Button

J(Tone) Button

Charge Contact

Page Button

Receiver

(Function/OK) Button

P(Talk Off/Power) Button

	1	2
	4	2	3	W(Cancel) Button
		5	3

			6
	7
		8

			9
		0	9
		0

Charge Contact

N (Intercom) Button

M (Recall) Button

Microphone

10

Image 10

Contents Operating Instructions Charge the batteries for approx hours before initial useAccessories included Dear purchaserSafety Instructions EnvironmentContents Programmable Functions Useful Information On the Base Unit Programmable Functions OnGetting Started Connection of Power SupplyConnections Battery Strength Installing the Batteries in the HandsetBattery Charge Battery InformationRemember to charge the new batteries after replacement see Battery CautionBattery Replacement Getting StartedWall Mounting Base Unit Location of ControlsHandset Handset Display Symbols UsedDisplays IconsBasic Start-up Operations To Redial the Last Number Dialled Making CallsTo Dial after Confirming the Entered Number To Redial after Confirming the Numbers in Redial MemoryTo Edit/Clear Numbers in the Redial List To Select the Receiver VolumeMaking Calls Direct CallTo Turn the Handset Ringer Off Temporarily Answering CallsAuto Talk Lighted Handset KeypadStoring Phone Numbers in Memory Speed DiallingDialling a Stored Number Speed Dial Menu S U to select noSaving Numbers in Speed Dial List save speed Speed DiallingDisplay number to be saved How Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Caller ID Service Caller ID Sub-MenuViewing the Caller List Using the Caller ListTo exit the list, Z W or P Calling Back from the Caller List Using the Caller ListFor Optional Multi-Unit Users Operating More than One HandsetIntercom between Handsets Paging/IntercomPaging All Handsets from the Base Unit Transferring a Call from One Handset to AnotherPaging/Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerConference Using the Recall Feature Special FeaturesHow to Use the Pause Feature Temporary Tone DiallingTo Cancel the Key Lock Special FeaturesSetting the Key Lock on Y for more than 2 secondsSummary of Programmable Functions On the HandsetTo Stop the Alarm Setting Time Alarm FunctionSet Time of Alarm set time Ringer vol Set Battery Low Tone ON/OFF battery low on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Standby Mode Display standby mode Setting Display OptionsSelect the Talk Mode Display talk mode Set Call Prohibition call bar see Setting Call OptionSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Select Battery Type battery type Setting Other OptionsSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registering a Handset to a Base Unit register hs RegistrationHold Ï on base unit for 10 secs. a confirmation tone sounds Cancelling a Base Unit cancel base ZV or YSpecified Base Unit Access eg. base1 Automatic Base Unit Access autoSelect Base Unit select bs Reset Handset reset hs Function Initial SettingProgrammable Functions On the Base Unit Bell SelectionTo Select the Dialling Mode To Select the Base Unit Ringer VolumeSetting the Clock Programmable Functions On the Base Unit Select Earth/Flash ModeSelect Pause Timing Cancelling a Handset Set Base Unit PINReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Problem Remedy Before Requesting HelpOutlet may be interfering with the Caller ID Adding Another Phone Before Requesting Help28426English 13/2/01 358 pm 28426English 13/2/01 358 pm PQQX13170ZA KU0601LL0