Panasonic KX-TCD700BX Getting Started, Battery Caution, Battery Replacement, Base Unit Location

Page 8

31939_KX-TCD700CX_Czech 18/6/01 1:54 pm Page 8

➡Getting Started

Battery Caution:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1.Use only the batteries specified.

2.Do not use non-rechargeable batteries.

3.Do not mix old and new batteries.

4.Do not dispose of the batteries in a fire, they may explode. Check with local waste management codes for special disposal instructions.

5.Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

6.Exercise care in handling the batteries in order not to short the batteries with conductive materials such as rings, bracelets, and keys. The batteries and/or conductor may overheat and cause burns.

7.Charge the batteries provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

Battery Replacement

If “Û” flashes after a few telephone calls even when the handset batteries have been fully charged, it is time to replace the batteries with new ones.

Remember to charge the new batteries after replacement (see page 7).

•Discard defective batteries as soon as possible. Defective batteries may leak into the unit.

Base Unit Location

For maximum distance and noise-free operation, the recommended base unit location is:

•Away from electrical appliances such as TV, radio, personal computer or another telephone.

•In a convenient high and central location.

8

Image 8

Contents Operating Instructions Charge the batteries for approx hours before initial useAccessories included Dear purchaserSafety Instructions EnvironmentContents Programmable Functions Useful Information On the Base Unit Programmable Functions OnConnections Connection of Power SupplyGetting Started Installing the Batteries in the Handset Battery ChargeBattery Strength Battery InformationBattery Caution Battery ReplacementRemember to charge the new batteries after replacement see Getting StartedWall Mounting Handset Location of ControlsBase Unit Symbols Used DisplaysHandset Display IconsBasic Start-up Operations Making Calls To Dial after Confirming the Entered NumberTo Redial the Last Number Dialled To Redial after Confirming the Numbers in Redial MemoryTo Select the Receiver Volume Making CallsTo Edit/Clear Numbers in the Redial List Direct CallAnswering Calls Auto TalkTo Turn the Handset Ringer Off Temporarily Lighted Handset KeypadDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory Speed Dial Menu S U to select noDisplay number to be saved Speed DiallingSaving Numbers in Speed Dial List save speed Checking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Service Caller ID Sub-MenuTo exit the list, Z W or P Using the Caller ListViewing the Caller List Using the Caller List For Optional Multi-Unit UsersCalling Back from the Caller List Operating More than One HandsetPaging/Intercom Paging All Handsets from the Base UnitIntercom between Handsets Transferring a Call from One Handset to AnotherConference Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom Special Features How to Use the Pause FeatureUsing the Recall Feature Temporary Tone DiallingSpecial Features Setting the Key Lock onTo Cancel the Key Lock Y for more than 2 secondsSummary of Programmable Functions On the HandsetSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm Ringer vol Setting Tone Options Set Range Warning Alarm ON/OFF range alarm on/offSet Battery Low Tone ON/OFF battery low on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Direct Call ON/OFF set direct on/off see Setting Call OptionSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs. a confirmation tone sounds RegistrationRegistering a Handset to a Base Unit register hs Cancelling a Base Unit cancel base ZV or YSelect Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base1 Reset Handset reset hs Function Initial SettingProgrammable Functions On the Base Unit Bell SelectionSetting the Clock To Select the Base Unit Ringer VolumeTo Select the Dialling Mode Select Pause Timing Select Earth/Flash ModeProgrammable Functions On the Base Unit Cancelling a Handset Set Base Unit PINReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Problem Remedy Before Requesting HelpOutlet may be interfering with the Caller ID Adding Another Phone Before Requesting Help28426English 13/2/01 358 pm 28426English 13/2/01 358 pm PQQX13170ZA KU0601LL0