Panasonic KX-TCD700BX operating instructions Caller ID Service, Checking the Number of New Calls

Page 19

31939_KX-TCD700CX_Czech 18/6/01 1:54 pm Page 19

Caller ID Service

Caller ID, where available, is a telephone company service. After subscribing to Caller ID, this phone will display the caller’s phone number.

This unit is compatible with a Caller ID service offered by your telephone company. If you should subscribe to a Caller ID service, the calling party’s information will be shown on the handset display after the first ring.

You cannot access the Caller ID service while using the handset and base unit for an internal call.

How Caller Information is Displayed when a Call is Received

Incoming Call

Caller’s phone number is displayed after first ring.

888888888888

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

0123456789

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

1. Z O (Length of call is displayed).

Caller’s phone number cannot be displayed in the following cases:

If the caller dialled from an area which does not provide a Caller ID service, the display will show.

– If the caller has requested not to display his/her phone number, the display will show.

If your unit is connected to a telephone line or a PBX which does not support Caller ID service, you cannot access those services.

00-00-00

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

out of area

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

private

ÂÊ Á Ë È Í

ÎÏ Ô Ó Ò

Checking the Number of New Calls

In the standby mode, when new calls have been received, the display shows the number of new calls.

For example if you have received 10 new calls the display will show the following.

-1-888888810

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

19

Image 19
Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Accessories includedEnvironment Safety InstructionsContents Programmable Functions On Programmable Functions Useful Information On the Base UnitGetting Started Connection of Power SupplyConnections Battery Information Installing the Batteries in the HandsetBattery Charge Battery StrengthGetting Started Battery CautionBattery Replacement Remember to charge the new batteries after replacement seeWall Mounting Base Unit Location of ControlsHandset Icons Symbols UsedDisplays Handset DisplayBasic Start-up Operations To Redial after Confirming the Numbers in Redial Memory Making CallsTo Dial after Confirming the Entered Number To Redial the Last Number DialledDirect Call To Select the Receiver VolumeMaking Calls To Edit/Clear Numbers in the Redial ListLighted Handset Keypad Answering CallsAuto Talk To Turn the Handset Ringer Off TemporarilyStoring Phone Numbers in Memory Speed DiallingDialling a Stored Number S U to select no Speed Dial MenuSaving Numbers in Speed Dial List save speed Speed DiallingDisplay number to be saved How Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Caller ID Sub-Menu Caller ID ServiceViewing the Caller List Using the Caller ListTo exit the list, Z W or P Operating More than One Handset Using the Caller ListFor Optional Multi-Unit Users Calling Back from the Caller ListTransferring a Call from One Handset to Another Paging/IntercomPaging All Handsets from the Base Unit Intercom between HandsetsPaging/Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerConference Temporary Tone Dialling Special FeaturesHow to Use the Pause Feature Using the Recall FeatureY for more than 2 seconds Special FeaturesSetting the Key Lock on To Cancel the Key LockOn the Handset Summary of Programmable FunctionsTo Stop the Alarm Setting Time Alarm FunctionSet Time of Alarm set time Ringer vol Set Key Confirmation Tone ON/OFF key tone on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Battery Low Tone ON/OFF battery low on/offSelect the Standby Mode Display standby mode Setting Display OptionsSelect the Talk Mode Display talk mode Set Call Prohibition call bar see Setting Call OptionSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Select Battery Type battery type Setting Other OptionsSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registering a Handset to a Base Unit register hs RegistrationHold Ï on base unit for 10 secs. a confirmation tone sounds ZV or Y Cancelling a Base Unit cancel baseSpecified Base Unit Access eg. base1 Automatic Base Unit Access autoSelect Base Unit select bs Function Initial Setting Reset Handset reset hsBell Selection Programmable Functions On the Base UnitTo Select the Dialling Mode To Select the Base Unit Ringer VolumeSetting the Clock Programmable Functions On the Base Unit Select Earth/Flash ModeSelect Pause Timing Set Base Unit PIN Cancelling a HandsetFunction Initial Setting Reset Base UnitOption Covers Using the Belt Clip Before Requesting Help Problem RemedyOutlet may be interfering with the Caller ID Before Requesting Help Adding Another Phone28426English 13/2/01 358 pm 28426English 13/2/01 358 pm PQQX13170ZA KU0601LL0