Panasonic KX-TCD700BX operating instructions Outlet may be interfering with the Caller ID

Page 48

Page 51

Problem

Remedy

While programming or searching, • To answer the call, lift the handset or Z O.

the unit starts to ring and stops Start again from the beginning after hanging up. the program/search.

The unit does not display the

• Other telephone equipment may be interfering with

caller’s phone numbers.

your phone. Disconnect them and try again.

 

• Other electrical appliances connected to the same

 

outlet may be interfering with the Caller ID

 

information. Telephone line noise may be affecting

 

the Caller ID information.

 

 

Ï does not function.

• The handset is too far from the base unit.

 

• The handset is engaged in an outside call.

 

 

You cannot redial.

• If the last number dialled was more than 24 digits

 

long, the number will not be redialled correctly.

 

 

The paged handset does not

• The handset is not in the same radio area.

answer.

• The handset is engaged in an outside call.

 

• The handset has been cancelled or has not been

 

registered. Register the handset to the base unit

 

(p.36).

 

 

While using the intercom, two tones

• A call is being received. To answer, Z P then

sound.

O.

 

 

The unit misdials when connected

• Check the pause function (p.25).

to a PBX.

 

 

 

You cannot register the handset

• The base unit has registered a maximum of 6

in the base unit.

handsets or the handset has registered a maximum

 

of 4 base units.

 

• A wrong base unit password was entered. Enter the

 

correct password.

 

• There is interference from other electrical units,

 

locate the handset and base unit away from them.

 

• You must finish registration within 1 minute after the

 

ringer tone sounds, or programming will be

 

cancelled (p.36).

 

 

The battery strength is not

• Check that the battery type selection is correct

displayed correctly.

(p.34).

48

Image 48
Contents Operating Instructions Charge the batteries for approx hours before initial useAccessories included Dear purchaserSafety Instructions EnvironmentContents Programmable Functions Useful Information On the Base Unit Programmable Functions OnConnection of Power Supply Getting StartedConnections Installing the Batteries in the Handset Battery ChargeBattery Strength Battery InformationBattery Caution Battery ReplacementRemember to charge the new batteries after replacement see Getting StartedWall Mounting Location of Controls Base UnitHandset Symbols Used DisplaysHandset Display IconsBasic Start-up Operations Making Calls To Dial after Confirming the Entered NumberTo Redial the Last Number Dialled To Redial after Confirming the Numbers in Redial MemoryTo Select the Receiver Volume Making CallsTo Edit/Clear Numbers in the Redial List Direct CallAnswering Calls Auto TalkTo Turn the Handset Ringer Off Temporarily Lighted Handset KeypadSpeed Dialling Storing Phone Numbers in MemoryDialling a Stored Number Speed Dial Menu S U to select noSpeed Dialling Saving Numbers in Speed Dial List save speedDisplay number to be saved Caller ID Service How Caller Information is Displayed when a Call is ReceivedChecking the Number of New Calls Caller ID Service Caller ID Sub-MenuUsing the Caller List Viewing the Caller ListTo exit the list, Z W or P Using the Caller List For Optional Multi-Unit UsersCalling Back from the Caller List Operating More than One HandsetPaging/Intercom Paging All Handsets from the Base UnitIntercom between Handsets Transferring a Call from One Handset to AnotherHandset 1 Z P Handset 2 When the unit rings, Z O to answer Paging/IntercomConference Special Features How to Use the Pause FeatureUsing the Recall Feature Temporary Tone DiallingSpecial Features Setting the Key Lock onTo Cancel the Key Lock Y for more than 2 secondsSummary of Programmable Functions On the HandsetSetting Time Alarm Function To Stop the AlarmSet Time of Alarm set time Ringer vol Setting Tone Options Set Range Warning Alarm ON/OFF range alarm on/offSet Battery Low Tone ON/OFF battery low on/off Set Key Confirmation Tone ON/OFF key tone on/offSetting Display Options Select the Standby Mode Display standby modeSelect the Talk Mode Display talk mode Setting Call Option Set Call Prohibition call bar seeSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Setting Other Options Select Battery Type battery typeSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registration Registering a Handset to a Base Unit register hsHold Ï on base unit for 10 secs. a confirmation tone sounds Cancelling a Base Unit cancel base ZV or YAutomatic Base Unit Access auto Specified Base Unit Access eg. base1Select Base Unit select bs Reset Handset reset hs Function Initial SettingProgrammable Functions On the Base Unit Bell SelectionTo Select the Base Unit Ringer Volume To Select the Dialling ModeSetting the Clock Select Earth/Flash Mode Programmable Functions On the Base UnitSelect Pause Timing Cancelling a Handset Set Base Unit PINReset Base Unit Function Initial SettingOption Covers Using the Belt Clip Problem Remedy Before Requesting HelpOutlet may be interfering with the Caller ID Adding Another Phone Before Requesting Help28426English 13/2/01 358 pm 28426English 13/2/01 358 pm PQQX13170ZA KU0601LL0