Panasonic KX-TCD700BX operating instructions Adding Another Phone, Before Requesting Help

Page 49

➡Before Requesting Help

Problem	Remedy
“Û” flashes or the unit bleeps	• Charge the batteries fully (p.7).
every 15 seconds.

You charged the batteries fully,	• Clean the charge contacts and charge again (p.7).
but “Û” flashes.	• Install new batteries (p.7).

Adding Another Phone

This unit will not function during a power failure. To connect a standard telephone on the same line, use a T-adaptor.

To Telephone Socket

T-Adaptor

Telephone Line Cord

Standard Telephone

Image 49

Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Accessories includedEnvironment Safety InstructionsContents Programmable Functions On Programmable Functions Useful Information On the Base UnitGetting Started Connection of Power SupplyConnections Battery Charge Installing the Batteries in the HandsetBattery Strength Battery InformationBattery Replacement Battery CautionRemember to charge the new batteries after replacement see Getting StartedWall Mounting Base Unit Location of ControlsHandset Displays Symbols UsedHandset Display IconsBasic Start-up Operations To Dial after Confirming the Entered Number Making CallsTo Redial the Last Number Dialled To Redial after Confirming the Numbers in Redial MemoryMaking Calls To Select the Receiver VolumeTo Edit/Clear Numbers in the Redial List Direct CallAuto Talk Answering CallsTo Turn the Handset Ringer Off Temporarily Lighted Handset KeypadStoring Phone Numbers in Memory Speed DiallingDialling a Stored Number S U to select no Speed Dial MenuSaving Numbers in Speed Dial List save speed Speed DiallingDisplay number to be saved How Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Caller ID Sub-Menu Caller ID ServiceViewing the Caller List Using the Caller ListTo exit the list, Z W or P For Optional Multi-Unit Users Using the Caller ListCalling Back from the Caller List Operating More than One HandsetPaging All Handsets from the Base Unit Paging/IntercomIntercom between Handsets Transferring a Call from One Handset to AnotherPaging/Intercom Handset 1 Z P Handset 2 When the unit rings, Z O to answerConference How to Use the Pause Feature Special FeaturesUsing the Recall Feature Temporary Tone DiallingSetting the Key Lock on Special FeaturesTo Cancel the Key Lock Y for more than 2 secondsOn the Handset Summary of Programmable FunctionsTo Stop the Alarm Setting Time Alarm FunctionSet Time of Alarm set time Ringer vol Set Range Warning Alarm ON/OFF range alarm on/off Setting Tone OptionsSet Battery Low Tone ON/OFF battery low on/off Set Key Confirmation Tone ON/OFF key tone on/offSelect the Standby Mode Display standby mode Setting Display OptionsSelect the Talk Mode Display talk mode Set Call Prohibition call bar see Setting Call OptionSet Direct Call ON/OFF set direct on/off see Set Direct Call ON/OFF set direct on/off Select Battery Type battery type Setting Other OptionsSet Auto Talk ON/OFF auto talk Change Handset PIN hspin change Registering a Handset to a Base Unit register hs RegistrationHold Ï on base unit for 10 secs. a confirmation tone sounds ZV or Y Cancelling a Base Unit cancel baseSpecified Base Unit Access eg. base1 Automatic Base Unit Access autoSelect Base Unit select bs Function Initial Setting Reset Handset reset hsBell Selection Programmable Functions On the Base UnitTo Select the Dialling Mode To Select the Base Unit Ringer VolumeSetting the Clock Programmable Functions On the Base Unit Select Earth/Flash ModeSelect Pause Timing Set Base Unit PIN Cancelling a HandsetFunction Initial Setting Reset Base UnitOption Covers Using the Belt Clip Before Requesting Help Problem RemedyOutlet may be interfering with the Caller ID Before Requesting Help Adding Another Phone28426English 13/2/01 358 pm 28426English 13/2/01 358 pm PQQX13170ZA KU0601LL0