Panasonic KX-TCD700BX operating instructions Change Handset PIN hspin change

Page 35

31939_KX-TCD700CX_Czech 18/6/01 1:54 pm Page 35

•Change Handset PIN (hspin change)

•You can program a 4 digit password for the handset. The factory pre-set is 0000. Changing the password may prevent the unauthorised use of your unit by another person.

(Standby Mode)

-1- 01

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z Y or V

new speed

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z S or U

setting hs

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z Y or V

time alarm

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z S or U

other opt

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z Y or V

hspin change

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Z

Yor V

•Enter current PIN

(old pin). If PIN is incorrect, error tone sounds.

old pin8œœœœ

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•Enter new PIN (4 digits).

new pin8œœœœ

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

Note: The PIN is not displayed É is deleted as a number is entered.

verify88œœœœ

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•Re-enter new PIN (verify).

•If PIN is incorrect, error tone sounds. (Display returns to new pin).

If PIN is correct, confirmation tone sounds.

hspin change

ÂÊ Á Ë È Í

ÎÏ  Ô Ó Ò

•Z P or (W 3 times) to return to standby mode.

NOTE: Once you have programmed the password, you cannot confirm it. We recommend you write down the password. If you forget it, please consult your nearest Panasonic Service Centre.

35

Image 35

Contents Charge the batteries for approx hours before initial use Operating InstructionsDear purchaser Accessories includedEnvironment Safety InstructionsContents Programmable Functions On Programmable Functions Useful Information On the Base UnitConnections Connection of Power SupplyGetting Started Battery Information Installing the Batteries in the HandsetBattery Charge Battery StrengthGetting Started Battery CautionBattery Replacement Remember to charge the new batteries after replacement seeWall Mounting Handset Location of ControlsBase Unit Icons Symbols UsedDisplays Handset DisplayBasic Start-up Operations To Redial after Confirming the Numbers in Redial Memory Making CallsTo Dial after Confirming the Entered Number To Redial the Last Number DialledDirect Call To Select the Receiver VolumeMaking Calls To Edit/Clear Numbers in the Redial ListLighted Handset Keypad Answering CallsAuto Talk To Turn the Handset Ringer Off TemporarilyDialling a Stored Number Speed DiallingStoring Phone Numbers in Memory S U to select no Speed Dial MenuDisplay number to be saved Speed DiallingSaving Numbers in Speed Dial List save speed Checking the Number of New Calls Caller ID ServiceHow Caller Information is Displayed when a Call is Received Caller ID Sub-Menu Caller ID ServiceTo exit the list, Z W or P Using the Caller ListViewing the Caller List Operating More than One Handset Using the Caller ListFor Optional Multi-Unit Users Calling Back from the Caller ListTransferring a Call from One Handset to Another Paging/IntercomPaging All Handsets from the Base Unit Intercom between HandsetsConference Handset 1 Z P Handset 2 When the unit rings, Z O to answerPaging/Intercom Temporary Tone Dialling Special FeaturesHow to Use the Pause Feature Using the Recall FeatureY for more than 2 seconds Special FeaturesSetting the Key Lock on To Cancel the Key LockOn the Handset Summary of Programmable FunctionsSet Time of Alarm set time Setting Time Alarm FunctionTo Stop the Alarm Ringer vol Set Key Confirmation Tone ON/OFF key tone on/off Setting Tone OptionsSet Range Warning Alarm ON/OFF range alarm on/off Set Battery Low Tone ON/OFF battery low on/offSelect the Talk Mode Display talk mode Setting Display OptionsSelect the Standby Mode Display standby mode Set Direct Call ON/OFF set direct on/off see Setting Call OptionSet Call Prohibition call bar see Set Direct Call ON/OFF set direct on/off Set Auto Talk ON/OFF auto talk Setting Other OptionsSelect Battery Type battery type Change Handset PIN hspin change Hold Ï on base unit for 10 secs. a confirmation tone sounds RegistrationRegistering a Handset to a Base Unit register hs ZV or Y Cancelling a Base Unit cancel baseSelect Base Unit select bs Automatic Base Unit Access autoSpecified Base Unit Access eg. base1 Function Initial Setting Reset Handset reset hsBell Selection Programmable Functions On the Base UnitSetting the Clock To Select the Base Unit Ringer VolumeTo Select the Dialling Mode Select Pause Timing Select Earth/Flash ModeProgrammable Functions On the Base Unit Set Base Unit PIN Cancelling a HandsetFunction Initial Setting Reset Base UnitOption Covers Using the Belt Clip Before Requesting Help Problem RemedyOutlet may be interfering with the Caller ID Before Requesting Help Adding Another Phone28426English 13/2/01 358 pm 28426English 13/2/01 358 pm PQQX13170ZA KU0601LL0