Panasonic KX-TC1220NZW To check the time and date, For Caller ID service users p

Page 15

8	Press á (Next key).
9	Enter the current date by using a 4-digit
9	number.
	(Ex. To set Dec. 27, enter “2712”.)
10	Press á (Save key).
10	•A beep sounds.

•The clock starts working.

09:30P 01.01 Enter day.month

H=Save

09:30P 27.12 Enter day.month

H=Save

09:30P 27.12 2001

Preparation

•You can go back to the previous display by pressing Ü, when setting the time and date.

•If 3 beeps sound when entering the time and date, a wrong number was entered. Enter the correct time and date.

To check the time and date

You can check the current time and date in the standby mode.

Lift the handset off the base unit and press /(EXIT/CH) twice.

OR

When the handset is off the base unit, press /(EXIT/CH) once.

•The current time and date is displayed for 30 seconds. To return to the standby mode, press /(EXIT/CH).

ON

OFF

TALK

FUNCTIONEDIT

1 2

4 5

INTERCOM

EXITCH 3

6

/(EXIT/CH)

If a power failure occurs, you have to readjust the time and date. If you use the handset for making/answering calls or remote operation without adjusting the time and date, the display in step 1 appears for 5 seconds after “Off” is displayed.

For Caller ID service users (p. 27)

•The Caller ID information will re-set the clock after the ﬁrst ring if the adjusted time and/or date is incorrect. However, if the time has not previously been set, the Caller ID information will not adjust the clock.

•The caller ID information will automatically adjust the clock for daylight saving time.

15

Image 15

Contents Operating Instructions Charge the battery for about 10 hours before initial useAccessories included Before Initial UseFor your future reference Battery Charge For Best PerformanceBase Unit Location Contents Call Waiting and Caller ID Compatible For Australia only Transferring a Call Using the IntercomHandset Location of ControlsBase unit 0266667777 DisplayPreparation Display Connections SettingsDisplay prompt Battery strength Installing the Battery in the HandsetSettings Battery strengthRecharge Battery informationAfter your Panasonic battery is fully charged p Standby mode While the handset is off the base unitTime and Date Adjustment Make sure the unit is in the standby mode initiallyYou can select AM/PM or 24-hour clock by programming To check the time and date For Caller ID service users pProgrammable Functions To select the recall time pDuring programming Press á Yes key Setting the Auto Talk FeaturePress Ö or Ñ repeatedly until the arrow Points to ProgramWith the base unit Selecting the Ringer VolumeProgrammable Functions With the handsetPress Ö or Ñ to select the desired Setting the LCD ContrastWhile the arrow points to LCD Contrast, press á Yes keyFor New Zealand Users Storing Your Area CodeTo store your area code To erase your area codeTo redial the last number dialled on the handset Making CallsWith the Handset If noise interferes with the conversationMaking Calls With the Base Unit Digital Duplex Speakerphone To release the hold To adjust the speaker volume 8 levels while talkingTo redial the last number dialled on the base unit To put a call on holdUseful information Simultaneous Keypad DiallingTalk into the MIC Answering CallsAuto Talk If the handset is off the base unit, press Talkﬁrst ring Caller ID ServiceHow caller information is displayed when a call is received Handset display shows Caller’s phone number afterWhile the handset is off the base unit Caller ID ServiceTo check the number of new calls While the handset is on the base unitTo exit the list, press EXIT/CH Using the Caller ListViewing the Caller List To check who has called, follow the steps belowTo exit the Caller List Using the Caller ListEx. When you search from the most recent call To return to the previous callerLift the handset off the base unit Calling Back from the Caller ListPress FUNCTION/EDIT, then press Ü to erase the digit Editing the Caller’s Phone NumberTo add a number To erase the numberStoring Caller List Information in the Directory When the caller’s name is not displayed in the Caller ListTo erase a speciﬁc caller from the Caller List Erasing Caller List InformationTo erase all entries in the Caller List To erase a stored number Speed DiallerStoring Phone Numbers in Memory Dialling a Stored NumberStoring Names and Numbers in the Directory Using the DirectoryFor New Zealand Users Selecting Characters to Enter Names If you make a mistake while entering a nameNumber of times key is pressed Keys Using the Directory For example, to enter Tom JonesEight times To search for a name by initial Finding Items in the DirectoryDialling from the Directory Index tableKeys Index Editing an Item in the Directory Erasing an Item from the Directory Directory item you want to erasePress Ö or Ñ to select Clear Handset Press Intercom to answer IntercomPaging the base unit from the handset Paging the handset from the base unit Handset locatorFrom the base unit to the handset Transferring a Call Using the IntercomIntercom From the handset to the base unitSpecial Features How to Use the Pause ButtonFor Analog PBX Line/Long Distance Service Users Recall Button Automatic Security Code SettingSpecial Features Call Waiting and Caller ID CompatibleSelecting the recall time Points to Set recallDesired time is displayed Push it in the direction of the arrow Wall MountingTuck the telephone line cord inside Wall mounting adaptor, thenWall Template To charge the handset batteryClose the cover. Make sure you charge Battery ReplacementNew battery for about 10 hours so That the battery strength indicator appears pAdding Another Phone Before Requesting Help ProblemRemedyProblem Remedy Before Requesting Help For Australian CustomersFor New Zealand Customers Placement Safety InstructionsSafety Installations EnvironmentFor New Zealand Users Only Installation Important Information For Australia onlyInstructions to customer PQQX13215ZA-BM S1001-0 Service difficulties