Panasonic VL-SW250BX Answering a call by voice sensor Voice answer mode, Microphone, Menu OFF

Page 18

Doorphone

Answering a call

When you receive a call from a door station, the main monitor station and the sub monitor station ring and the TALK indicators flash. You can monitor the visitor on the monitor display before answering a call.

{VOLUME}

XX

{PAGE}

{▲} {▲} {▲} {

▲}

{VOICE CHANGER}

Microphone

{MENU}

{MENU}

{D}

{OFF}

{TALK} and {OFF} indicator

TALK indicator {TALK}

Microphone

1

2

3

When a ringer tone is heard, press {TALK}.

Speak to the visitor within 50 cm of the microphone.

LSpeak alternately with the visitor.

(If you and the visitor speak at the same time, you will not hear each other.)

To end the conversation, press {OFF}.

Note:

LIf you do not answer a door call within 30 seconds, the display will turn off.

A conversation will be automatically disconnected in about 90 seconds and then the display will turn off. LThe image taken by the door station is automatically recorded (page 24).

When using an additional door station:

LWhen you receive another call from the other door station during a conversation, see page 22.

Answering a call by voice sensor (Voice answer mode)

This mode allows you to answer a call by voice without pressing {TALK}. (You can operate this feature in the same way by using either the main monitor station or the sub monitor station.)

Voice answer must be set “ON” beforehand (page 37, 41).

1 When a ringer tone is heard, answer with a clear voice such as “Yes?” or “Hello?”. LWhen a beep sounds, you can talk to the visitor.

Note:

LMake sure you are within about 50 cm of the main monitor station or the sub monitor station. LThe visitor cannot hear your initial reply when you answer with voice.

LYour initial reply should be brief (less than 1 second), otherwise the voice answer mode will not start.

LIf a visitor calls you, a loud, brief sound (such as a dog’s bark) may start the voice answer mode even though you have not replied by voice.

LWhen you locate the sub monitor station near the main monitor station, the voice answer mode may be started by a ringer tone.

LThe voice answer mode is also available for paging calls.

18

SW250BX_OI.indb 18

2010/08/25 15:58:31

Image 18
Contents Attached Installation Guide Thank you for purchasing a Panasonic productPreparation IntroductionImportant Information DoorphoneIncluded items Accessory informationProduct names used in these Operating Instructions VL-SW250BXWhen using with a lobby station Additional/replacement accessoriesAccessory items Order number Compatible Panasonic PBXsInstallation For your safetyPower connection Operating safeguardsImportant safety instructions Installation and relocationBattery Before using For best performanceEnvironment Privacy and rights of portrait Other informationTapping OthersLocation of controls Door stationMain monitor station Display during operation Press Volume dMonitor display Main monitor station Operation guidanceSub monitor station Charge contacts Battery coverRear view Speaker Charge contacts Metallic parts Charger Charger standMonitor display Sub monitor station OFFBack Next LImages on the monitor displayTo assemble the charger stand Charging the sub monitor stationPad at the back To remove the charger standSetting the date and time Volume Voice ChangerVoice Changer Next Answering a call Answering a call by voice sensor Voice answer modeWhen using an additional door station MicrophoneAdjusting the speaker volume Main monitor station Features during a call or while monitoringAdjusting the display brightness Main monitor station Main monitor station onlySpeak while pressing and holding Talk Using Door KEY buttonTo speak to the visitor To hear the visitorTo transfer a call VolumeTransferring a call To receive a transferred callMonitor OFF Talk When answering a callMonitor Talk OFF NTo speak to the other partyMonitoring the outside Door station monitor When installing 2 door stationsPress Volume or page , then MonitorAuto recording NAuto image updateRecording an image PLAY/RECManual recording Press PLAY/RECPress D REC Viewing recorded images using the main monitor station Voice Changer Menu Volume OFFNTo view the next image Menu Play Voice Changer BackMenu Pause Menu MenuViewing recorded images using the sub monitor station NTo view a series of 8 continuous imagesImage status Button and guidance Operation BackSelect Volume MenuProtecting the recorded images To release protectionYou can erase unnecessary images Press Volume YESErasing an image Menu OFFVolume Menu OFF Caller ReceiverOFF Talk Adjusting the ringer volume Ringer tone patterns Changing the ringer toneMain monitor station Sub monitor station Sound Sound 1 REPEAT*1 Sound 2 REPEAT*1 Sound 3 REPEAT*1Volume or Setting Door KEY buttonPress Menu OK, then select Door KEY by pressing Volume or Press Menu OK, then select the desired item by pressingFunction list of the main monitor station How to change the function settingsItem function Setting Time and DateNORMAL, LOW PICTURES, 1 PictureTerminal 2 SIGNALS, 2 Terminals 1 Signal LobbyExternal Device REGISTRATION/CANCELLATION Registration Cancellation Demo ModeRing Volume Door HIGH, MEDIUM, LOW, OFF Function list of the sub monitor stationStation Disp REC Date ALWAYS, 3 SEC Init Settings YES, noVoice Answer ON, OFF ContrastExpanding your system with optional units Sub monitor station*1 Door station*1 Main monitor stationOperating the door opener Units required to be installed Adding a door stationUsing with Panasonic PBX Please use only a Panasonic PBXTo register a canceled sub monitor station page 46 again Using the main monitor stationUsing the sub monitor station Adding a sub monitor station RegistrationStatus indicator Setting a repeater RegistrationTo power outlet 100 240 V AC ProgramCanceling registration of the sub monitor station/repeater CancellationTroubleshooting Monitor display Problem Cause & SolutionAway from those appliances. Try again Problem Cause & Solution Conversation Doorphone/Intercom Problem Cause & SolutionRinger tone Problem Cause & Solution Sub monitor station/Battery Problem Cause & Solution Others Problem Cause & SolutionRemove the battery and insert it again Help Error messages Sub monitor station only Problem Cause & SolutionCleaning Battery replacementSub monitor station VL-W605BX SpecificationsMain monitor station VL-MW250BX Door station VL-V566BXLvoice Answer Lvoice Changer Lplay Lamp Flashing Function SettingsLring Volume Lring Tone Lcontrast LregistrationLoutgoing VOL For your future reference Attach your sales receipt here