Panasonic VL-SW250BX operating instructions Sub monitor station/Battery Problem Cause & Solution

Page 49

 

 

Help

N Sub monitor station/Battery

 

 

 

 

 

Problem

Cause & Solution

Page

flashes and 2 short beeps

LThe battery level is low. Charge the battery immediately.

16

sound.

 

 

 

 

 

Even if you place the sub monitor

LThe AC adaptor is disconnected from the power outlet or

16

station on the charger, the

the charger. Plug the AC adaptor into the power outlet or the

 

CHARGE indicator does not light

charger firmly.

 

up.

LThe sub monitor station is not placed on the charger correctly.

16

 

Replace it securely. (A short beep sounds and the CHARGE

 

 

indictor lights in solid red.)

52

 

LThe charge contacts are dirty. Clean them with a soft, dry cloth.

 

LThe battery is new or discharged. Place the sub monitor station

16

 

on the charger and wait for a few minutes.

 

 

 

 

The CHARGE indicator does not

LWhen the power of the main monitor station is turned off or

16

go off after the battery has been

“OUT OF RANGE” is displayed on the sub monitor station, the

 

charged for about 7 hours.

charging time will become longer. Make sure the power of the

 

 

main monitor station is turned on, and charge the sub monitor

 

 

station in a location near the main monitor station where “OUT

 

 

OF RANGE” disappears.

 

 

 

 

Even if the sub monitor station

LThe battery is at the end of its life. Replace the battery with a

52

has been charged, flashes

new one.

 

after using it a few times.

 

 

 

 

 

The sub monitor station, the AC

LThis is normal. (It may feel a little warmer in summer than in

―

adaptor, or the charger is warm.

winter.) If it feels very hot, disconnect the AC adapter from the

 

 

power outlet and contact our service personnel.

 

 

 

 

N Others

 

 

 

 

 

Problem

Cause & Solution

Page

The main monitor station, the

LThe unit does not work during a power failure. The date and

17

sub monitor station, and the

time may be reset to the default setting after a power failure. In

 

door station do not work during a

this case, set the date and time using the main monitor station

 

power failure.

again.

 

 

 

 

L“DEMO MODE” is displayed.

LDemo mode is activated. Change the setting to “OFF”.

39

LYou cannot answer the call or

 

 

make an intercom call.

 

 

 

 

 

LThe unit does not work with

LPerform the following operation (Reset).

 

correct operations.

Main monitor station:

10

LThe unit does not work properly.

Press the RESET switch on the bottom of the main monitor

 

station with a pointed object. (Recorded images and the

 

 

program settings are not affected.)

 

 

Sub monitor station:

―

 

Remove the battery and insert it again.

 

– Program settings are not affected.

 

 

– is displayed. However, the actual battery level is

 

 

maintained.

 

 

 

 

49

SW250BX_OI.indb 49

2010/08/25 15:58:39

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Thank you for purchasing a Panasonic product Attached Installation GuideImportant Information IntroductionPreparation DoorphoneProduct names used in these Operating Instructions Accessory informationIncluded items VL-SW250BXAccessory items Order number Additional/replacement accessoriesWhen using with a lobby station Compatible Panasonic PBXsPower connection For your safetyInstallation Operating safeguardsInstallation and relocation Important safety instructionsBattery For best performance Before usingEnvironment Tapping Other informationPrivacy and rights of portrait OthersDoor station Location of controlsMain monitor station Monitor display Main monitor station Press Volume dDisplay during operation Operation guidanceSub monitor station Rear view Speaker Charge contacts Metallic parts Charger Battery coverCharge contacts Charger standOFF Monitor display Sub monitor stationLImages on the monitor display Back NextPad at the back Charging the sub monitor stationTo assemble the charger stand To remove the charger standVolume Voice Changer Setting the date and timeVoice Changer Next When using an additional door station Answering a call by voice sensor Voice answer modeAnswering a call MicrophoneAdjusting the display brightness Main monitor station Features during a call or while monitoringAdjusting the speaker volume Main monitor station Main monitor station onlyTo speak to the visitor Using Door KEY buttonSpeak while pressing and holding Talk To hear the visitorTransferring a call VolumeTo transfer a call To receive a transferred callMonitor Talk OFF When answering a callMonitor OFF Talk NTo speak to the other partyPress Volume or page , then When installing 2 door stationsMonitoring the outside Door station monitor MonitorRecording an image NAuto image updateAuto recording PLAY/RECPress PLAY/REC Manual recordingPress D REC Voice Changer Menu Volume OFF Viewing recorded images using the main monitor stationNTo view the next image Menu Pause Voice Changer BackMenu Play Menu MenuNTo view a series of 8 continuous images Viewing recorded images using the sub monitor stationButton and guidance Operation Back Image statusProtecting the recorded images Volume MenuSelect To release protectionErasing an image Press Volume YESYou can erase unnecessary images Menu OFFCaller Receiver Volume Menu OFFOFF Talk Adjusting the ringer volume Main monitor station Sub monitor station Changing the ringer toneRinger tone patterns Sound Sound 1 REPEAT*1 Sound 2 REPEAT*1 Sound 3 REPEAT*1Press Menu OK, then select Door KEY by pressing Volume or Setting Door KEY buttonVolume or Press Menu OK, then select the desired item by pressingItem function Setting How to change the function settingsFunction list of the main monitor station Time and DatePICTURES, 1 Picture NORMAL, LOWLobby Terminal 2 SIGNALS, 2 Terminals 1 SignalExternal Device Demo Mode REGISTRATION/CANCELLATION Registration CancellationFunction list of the sub monitor station Ring Volume Door HIGH, MEDIUM, LOW, OFFStation Voice Answer ON, OFF Init Settings YES, noDisp REC Date ALWAYS, 3 SEC ContrastSub monitor station*1 Door station*1 Main monitor station Expanding your system with optional unitsUsing with Panasonic PBX Units required to be installed Adding a door stationOperating the door opener Please use only a Panasonic PBXUsing the sub monitor station Using the main monitor stationTo register a canceled sub monitor station page 46 again Adding a sub monitor station RegistrationTo power outlet 100 240 V AC Setting a repeater RegistrationStatus indicator ProgramCancellation Canceling registration of the sub monitor station/repeaterMonitor display Problem Cause & Solution TroubleshootingAway from those appliances. Try again Conversation Doorphone/Intercom Problem Cause & Solution Problem Cause & SolutionRinger tone Problem Cause & Solution Others Problem Cause & Solution Sub monitor station/Battery Problem Cause & SolutionRemove the battery and insert it again Help Sub monitor station only Problem Cause & Solution Error messagesBattery replacement CleaningMain monitor station VL-MW250BX SpecificationsSub monitor station VL-W605BX Door station VL-V566BXLring Volume Lring Tone Function SettingsLvoice Answer Lvoice Changer Lplay Lamp Flashing Lcontrast LregistrationLoutgoing VOL Attach your sales receipt here For your future reference
Top Page Image Contents