TABLE 8:
|
|
|
|
|
|
|
|
|
|
|
|
|
| MAC Address |
| The device ID in HEX format. This is needed for ISP troubleshooting. Note there |
| ||||||||
|
|
| are separate MAC addresses for the WAN side and the LAN side. |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| WAN IP Address |
| Shows WAN IP address of |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Product Model |
| Contains the product model info. |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Software Version |
| Program: This is the main software release. Boot and Loader are seldom |
| ||||||||
|
|
| changed. |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| System Up Time |
| Shows system up time since the last reboot. |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| PPPoE Link Up |
| Indicates whether the PPPoE connection is up if the |
| ||||||||
|
|
| modem. |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| NAT |
| Indicates the type of NAT connection used by the |
| ||||||||
|
|
| Based on STUN protocol. |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Port Status |
| Shows several information regarding the individual FXS ports. |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Port |
| Hook | Registration | DND | Forward | Busy | Delayed |
|
|
|
|
|
|
|
|
|
|
| Forward | Forward |
|
|
|
|
| FXS1 |
| On Hook | Registered | Yes | 613 |
|
|
|
|
|
|
| FXS2 |
| On Hook | Registered | No |
| 614 |
|
|
|
|
| • | Both FXS port1 and FXS port2 are registered with this SIP Server. |
|
| ||||||
|
|
| • | FXS Port 1 user has set Do Not Disturb. |
|
|
|
| ||||
|
|
| • | FXS Port 1 user has set his calls to be forwarded unconditionally to ext 613. |
| |||||||
|
|
| • | FXS Port 2 user has set his calls to forward to 614 when his phone is busy. |
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
ADVANCED USER CONFIGURATION
Log in to the advanced user configuration page the same way as for the basic configuration page. The password is case sensitive and the factory default password for Advanced User is “admin”.
Advanced User configuration includes the end user configuration and the advanced configurations including: a) SIP configuration, b) Codec selection, c) NAT Traversal Setting and d) other miscellaneous configuration.
TABLE 9:
Admin Password
This contains the password to access the Advanced Web Configuration page. This field is case sensitive. Only the administrator can configure the “Advanced Settings” page. Password field is purposely left blank for security reasons after clicking update and saved. The maximum password length is 25 characters.
Grandstream Networks, Inc. | Page 21 of 35 | |
| Firmware 1.0.0.39 | Last Updated: 03/2007 |