| Layer 3 QoS |
| This field defines the layer 3 QoS parameter which can be the value used for IP |
| ||
|
|
| Precedence or |
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
| Layer 2 QoS |
| Value used for layer 2 VLAN tag. Default setting is blank. |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| STUN Server |
| IP address or Domain name of the STUN server. |
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| This parameter specifies how often the |
| ||
|
|
| SIP server in order to keep the “hole” on the NAT open. Default is 20 seconds. |
| ||
|
|
| Minimum value is 20 seconds. |
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
| Firmware Upgrade |
| Enables |
| ||
| and Provisioning |
| TFTP or HTTP server. |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
| Via TFTP Server |
| This is the IP address of the configured TFTP server. | If selected and it is non- |
| |
|
|
| zero or not blank, the |
| ||
|
|
| image from the specified TFTP server at boot time. After 5 attempts, the system |
| ||
|
|
| will timeout and will start the boot process using the existing code image in the |
| ||
|
|
| Flash memory. If a TFTP server is configured and a new code image is |
| ||
|
|
| retrieved, the new downloaded image is saved into the Flash memory. |
| ||
|
|
| Note: Please do NOT interrupt the TFTP upgrade process (especially the power |
| ||
|
|
| supply) as this will damage the device. Depending on the network environment |
| ||
|
|
| this process can take up to 15 or 20 minutes. |
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
| Via HTTP Server |
| The URL for the HTTP server used for firmware upgrade and configuration via |
| ||
|
|
| HTTP. |
|
|
|
|
|
| For example, ttp://provisioning.mycompany.com:6688/Grandstream/1.0.0.34 |
| ||
|
|
| “:6688” is the specific TCP port where the HTTP server is listening; it can be |
| ||
|
|
| omitted if using default port 80. |
|
| |
|
|
| Note: If Auto Upgrade is set to No, |
| ||
|
|
| boot up. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Firmware Server |
| IP address or domain name of firmware server. |
|
| |
| Path |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Config Server Path |
| IP address or domain name of configuration server. |
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
| Firmware File Prefix |
| Default is blank. | If configured, |
| |
|
|
| This setting is useful for ITSPs. End user should keep it blank. |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Firmware File |
| Default is blank. End user should keep it blank. |
|
| |
| Postfix |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Config File Prefix |
| Default is blank. End user should keep it blank. |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Config File Postfix |
| Default is blank. End user should keep it blank. |
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
| Automatic Upgrade |
| Choose “Yes” to enable automatic upgrade and provisioning. In “Check for new |
| ||
|
|
| firmware every” field, enter the number of days to enable |
| ||
|
|
| server for firmware upgrade or configuration in the defined period of days. When |
| ||
|
|
| set to No, |
| ||
|
|
| Firmware.” Check New Firmware only when F/W pre/suffix changes” |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Grandstream Networks, Inc. | Page 22 of 35 | |||||
|
|
|
| Firmware 1.0.0.39 | Last Updated: 03/2007 | |